i have micromax q55... only disp problem.... so now my set i

[mobileservice]

i have a fresh micromax q55 ... my set problem is spme time lcd show & some time plane but set is working.... so i try to change flax ... so what happen in my set so my set is dead..... i open the set very care fully..... but i don't know how to dead my set so i try to flash my set... so give me a error so it's fiel problem ya hardware problem...

Code: Select all

COM15 [Serial2] selected
module  v4.04
Device: _Autodetect MT6228-6268 NAND
Checking data, wait...
Action: write flash NAND
write: Firmware
Micromax-Q55_TINNO35_09A_PCB01_GPRS_MT6235B_S01.E580_MP_F1_IN_MMX_05_10_2010-03-16_En.B4M.bin
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
nfi area detection...
bootloader version: TINNO35_09A_BOOTLOADER_V005_MT6235B_E580_MP_F1_IN_MMX_05_10.bin
nfi area detection (3 cores) finished: Ok
interface: BROM_DLL_v3.1016.00
Connect...
Phone should be Switched OFF !
Press and HOLD Power button now !
Connecting...
Booting...
Release Power button now !
bootcode current/expected: 3.2/3.2
CPU: 6235:8A04:8A01
status: FF
bbchip bl ver: FE
NOR flash chip: not installed
NAND flash id[0017]: 00AD:007600AD0076 [HYNIX] HY27XS08121M
chip size: 64Mb
page/spare size: 0200/0010
pages per block: 0020
bits i/o: 08
address cycles: 04
internal RAM size: 00010000
external RAM: absent
done
Set baudrate (460800)...
done
ram test...
testing 32bit...
32bit ram test passed
testing 16bit...
16bit ram test passed
ram test passed
===>  detect existing firmware structure...
detect ffs...
ffs offset/size: 02000000/02000000
firmware size: 32Mb
ffs size: 32Mb
detect sec ro...
detect custom parameters...
detect project-id...
project-id: E580_MP_F1_IN_MMX_05.10
detect NAND info...
number of areas/bytes to read: 1:00034000
reading (HW_STORAGE_NAND NUTL_READ_PAGE_ONLY)...
nfi area detection...
bootloader version: TINNO35_09A_BOOTLOADER_V005_MT6235B_E580_MP_F1_IN_MMX_05_10.bin
warning: id-page1 area is invalid
nfi area detection (0 cores) finished: failed
TCL-ID detection...
TCL-ID detection done
startup code area #1 detection...
number of areas/bytes to read: 1:00004000
reading (HW_STORAGE_NAND NUTL_READ_PAGE_ONLY)...
number of areas/bytes to read: 1:00004000
reading (HW_STORAGE_NAND NUTL_READ_PAGE_ONLY)...
startup code area #1 is invalid
startup code area #1 detection done
rom info ver: 07
sw version: TINNO35_09A_PCB01_GPRS_MT6235B_S01.E580_MP_F1_IN_MMX_05_10.BIN
project-id: E580_MP_F1_IN_MMX_05.10, 1908851D
code offset: 00000000
ffs offset/size [01]: 02000000/02000000
rom info structure: [protected] type (07), 1 record(s)
TCL-ID is absent
===>  done
nfi area detection...
bootloader version: TINNO35_09A_BOOTLOADER_V005_MT6235B_E580_MP_F1_IN_MMX_05_10.bin
nfi area detection (3 cores) finished: Ok
startup code area #1 check...
startup code area #1 calculation...
startup code area #1 fixed
number of cores: 3
loading files...
number of areas: 3
done
write...
write bootloader...
.
.
.
.
write core...
error: can not write flash (12): 0FAF:S_FT_NFB_DOWNLOAD_CODE_FAIL
error: last error: 0FAF:S_FT_NFB_DOWNLOAD_CODE_FAIL
Disconnect...
done
Finished, time used: 2 min 10 sec
Remove/Install battery now !

i will try to this file flash ... file download via infinity sarver... size is 18 mb
name : Micromax-Q55_TINNO35_09A_PCB01_GPRS_MT6235B_S01.E580_MP_F1_IN_MMX_05_10_2010-03-16_En.B4M.bin

[Support]

1. charge battery completely with external power supply
2. try to flash once again after you charge battery

[InfinityHelp]

hello!

flash file you used is wrong. I believe that this is a reason of such behavior.
but this will only make your software part correct. You still need to find and repair hardware reason
unfortunately i have no such file in infinity format.
i am uploading here full archive with all needed file for flashing
http://www.4shared.com/file/HpewWJAV/Q55.html

please post result