![Infinity Box Dongle [CM2] [BEST] Support](./styles/simplicity_blue/theme/images/logo.png){kind=logo}
Infinity-Box BEST NK2 v1.02 - Nokia 2 Full Support
ATTENTION: To use this software you should copy licence file license_xxxxxxxx.dat from /BEST/ folder to /BEST2/ folder
Nokia 2 Line:
E1A (TA-1007) WW (Nokia 2)
E1A (TA-1029) WW (Nokia 2)
E1I (TA-1011) WW (Nokia 2)
E1L (TA-1023) WW (Nokia 2)
E1L (TA-1035) WW (Nokia 2)
Nokia 2 Line features supported:
Main:
Identify ( Device Info / Version / Revision / SKU / Branding )
Format FS / Reset Settings
Reset FRP ( Google Reset Protection )
Repair:
Backup Device Security ( Include OTA details, Unique Device Details, QCN calibrations )
Restore Device Security
Repair Device Security
Repair Connectivity Items ( BT/WiFi )
Repair PSN
Repair Unknown BaseBand ( Security-Safe )
Firmware:
Write Firmware ( Infinity Format )
Read Firmware ( Infinity Format )
- Firmware made by BEST DO NOT DAMAGE any device security!
- Firmware made by BEST DO NOT DAMAGE any OTA compatibility!
- A-B OTA/UPDATE architecture supported!
Other:
Memory Tool ( Customization/Recovery/PartialFlashing )
Generic:
Identify in [FTM] mode updated ( NK 2-3-5-6-8 )
Unlock BootLoader ( NOKIA 8 and 2 LINE ONLY ): Allow boot device to Service Mode
Restore BootLoader ( NOKIA 8 and 2 LINE ONLY ): Allow restore device to normal mode
Changes:
FRP unlock improved
Repair Security revised
Firmware Reding improved
Firmware Flashing revised
Nokia 8 Recover Boot procedure revised ( new versions supported )
Boot speed optimized for Nokia 8 line
Supported devices list:
D1E (TA-1024) WW (Nokia 5)
D1L (TA-1027) WW (Nokia 5)
D1L (TA-1044) WW (Nokia 5)
D1A (TA-1053) WW (Nokia 5)
D1C (TA-1000) CN (Nokia 6)
D1C (TA-1003) CN (Nokia 6)
D1C (TA-1021) WW (Nokia 6)
D1C (TA-1025) WW (Nokia 6)
D1C (TA-1033) WW (Nokia 6)
D1C (TA-1039) WW (Nokia 6)
E1A (TA-1007) WW (Nokia 2)
E1A (TA-1029) WW (Nokia 2)
E1I (TA-1011) WW (Nokia 2)
E1L (TA-1023) WW (Nokia 2)
E1L (TA-1035) WW (Nokia 2)
NB1 4GiB (TA-1004) WW (Nokia 8)
NB1 4GiB (TA-1012) WW (Nokia 8)
NB1 6GiB (TA-1004) WW (Nokia 8)
NB1 6GiB (TA-1012) WW (Nokia 8)
B1C 4GiB (TA-1052) HK (Nokia 8)
Info:
- Use Nokia Care Emergency drivers ( same as for Lumia/NXP )
- Use Unlock/Restore BootLoader for Nokia 2 / Nokia 8 devices if can not enter device in EDL mode!
Software Updates and News
-
Support
- Posts: 4184
- Joined: 19 Oct 2011, 20:27
- Contact:
-
Support
- Posts: 4184
- Joined: 19 Oct 2011, 20:27
- Contact:
Re: Software Updates and News
CM2QLM Drivers v1.01 package released
CM2QLM_Drivers_v1.01 package uploaded in support area
CM2QLM_Drivers_v1.01 package uploaded in support area
-
Support
- Posts: 4184
- Joined: 19 Oct 2011, 20:27
- Contact:
Re: Software Updates and News
Infinity Chinese Miracle-2 QLM v1.16 - many new models and features
New CPU support
Qualcomm MSM 8905 (Mobile Platform 205)
Qualcomm MSM 8609 (SnapDragon 210)
Qualcomm MSM 8953 (SnapDragon 625 pro)
Supported CPU List:
Qualcomm MSM 8210 (SnapDragon 200)
Qualcomm MSM 8212 (SnapDragon 200)
Qualcomm MSM 8610 (SnapDragon 200)
Qualcomm MSM 8612 (SnapDragon 200)
Qualcomm MSM 8226 (SnapDragon 400)
Qualcomm MSM 8626 (SnapDragon 400)
Qualcomm MSM 8926 (SnapDragon 400)
Qualcomm MSM 8228 (SnapDragon 400)
Qualcomm MSM 8628 (SnapDragon 400)
Qualcomm MSM 8928 (SnapDragon 400)
Qualcomm APQ 8009 (SnapDragon 210)
Qualcomm MSM 8209 (SnapDragon 210)
Qualcomm MSM 8609 (SnapDragon 210)
Qualcomm MSM 8905 (Mobile Platform 205)
Qualcomm MSM 8909 (SnapDragon 210)
Qualcomm MSM 8916 (SnapDragon 410)
Qualcomm MSM 8917 (SnapDragon 425)
Qualcomm MSM 8929 (SnapDragon 415)
Qualcomm MSM 8936 (SnapDragon 610)
Qualcomm MSM 8937 (SnapDragon 430)
Qualcomm MSM 8939 (SnapDragon 615)
Qualcomm MSM 8940 (SnapDragon 435)
Qualcomm MSM 8974/A/AA/AB (SnapDragon 801)
Qualcomm MSM 8952 (SnapDragon 617)
Qualcomm MSM 8953 (SnapDragon 625/pro/plus)
Qualcomm MSM 8956 (SnapDragon 650)
Qualcomm MSM 8976 (SnapDragon 652)
Qualcomm MSM 8976 Pro (SnapDragon 653)
Qualcomm MSM 8992 (SnapDragon 808)
Qualcomm MSM 8994 (SnapDragon 810)
Qualcomm MSM 8996 (SnapDragon 820)
Qualcomm MSM 8996 Pro (SnapDragon 821)
Qualcomm MSM 8998 (SnapDragon 835)
- Main
FH Protocol updated and revised
Core revised, no more stuck boot problems
MSM8953 Pro new revision supported
MSM8905 supported
MSM8609 supported
Test support: SDM660
Test support: SDM630
- Flasher
SafeRegions detection improved
Factory firmware handling optimized
- More Secure and Generic types supported
+50 UNIQUE loaders included in internal DB!
Now QLM cover 230+ UNIQUE SECURE AND GENERIC TYPES! As nobody else
Software DO NOT require any kind of manual loaders selection, bruteforce etc.
MSM8909: ZTE, Asus, Alcatel and some Oppo
MSM8916: Coolpad, Alcatel and some Oppo
MSM8976: Vivo and others
MSM8953: Vivo and others
MSM8956: Generic Secure Chinese types, Alcatel, Lenovo and some others
MSM8936: Cover more Cyanogen based models ( include WileyFox and some rest )
MSM8937: Asus and other secure types
MSM8998: Nokia 8, and other Xiaomi models
MSM8905: Generic, LYF and other secure types
- Service operations improved
Enabled QCN operations
- Allow read calibrations and secure memory in XQCN format
- Allow write calibrations and security memory in XQCN format
- QCN verify, automatic security field update
Enabled Security repair feature
- Default "Clean memory mode" for start. Use with backup, wipe and restore
Basic DiagInfo reading during Diag operations
ADB layer activated
Enable Diag mode option released
- Allow enable diagnostic port on device [ ROOT REQUIRED! ]
- Firmware Reader engine updated
A/B memory architecture supported - allow read FW from newer devices with Android A/B update system!
New types supported ( brand-specific and generic types )
Files verification revised
-> Unlike other "solutions" CM2 make FIRMWARE BUT NOT A USELESS PLAIN DUMP ( i.e. cloning )
-> That means all device unique data, security etc. will remain safe after flashing !
- MemoryTool updated
Optimized WIPE operations
Fixed some VCL errors on Win7
BootConfigaration revised
- Other
DataDirect engine updated
Loader database updated
- 50+ new secure loaders
- Updated old and generic loaders
Some other improvements and fixes
Better UFS memory details logging
- Notes
-> Nokia QLM: since Nokia use own format of security and memory/ota structure - for COMPLETE service you should use BEST!
QLM offer basic support: FRP, Reset, Identify and backup features
-> Special THANKS to ALL our users who help us with sending reports, reporting problems and bugs, help with files and other things !
New CPU support
Qualcomm MSM 8905 (Mobile Platform 205)
Qualcomm MSM 8609 (SnapDragon 210)
Qualcomm MSM 8953 (SnapDragon 625 pro)
Supported CPU List:
Qualcomm MSM 8210 (SnapDragon 200)
Qualcomm MSM 8212 (SnapDragon 200)
Qualcomm MSM 8610 (SnapDragon 200)
Qualcomm MSM 8612 (SnapDragon 200)
Qualcomm MSM 8226 (SnapDragon 400)
Qualcomm MSM 8626 (SnapDragon 400)
Qualcomm MSM 8926 (SnapDragon 400)
Qualcomm MSM 8228 (SnapDragon 400)
Qualcomm MSM 8628 (SnapDragon 400)
Qualcomm MSM 8928 (SnapDragon 400)
Qualcomm APQ 8009 (SnapDragon 210)
Qualcomm MSM 8209 (SnapDragon 210)
Qualcomm MSM 8609 (SnapDragon 210)
Qualcomm MSM 8905 (Mobile Platform 205)
Qualcomm MSM 8909 (SnapDragon 210)
Qualcomm MSM 8916 (SnapDragon 410)
Qualcomm MSM 8917 (SnapDragon 425)
Qualcomm MSM 8929 (SnapDragon 415)
Qualcomm MSM 8936 (SnapDragon 610)
Qualcomm MSM 8937 (SnapDragon 430)
Qualcomm MSM 8939 (SnapDragon 615)
Qualcomm MSM 8940 (SnapDragon 435)
Qualcomm MSM 8974/A/AA/AB (SnapDragon 801)
Qualcomm MSM 8952 (SnapDragon 617)
Qualcomm MSM 8953 (SnapDragon 625/pro/plus)
Qualcomm MSM 8956 (SnapDragon 650)
Qualcomm MSM 8976 (SnapDragon 652)
Qualcomm MSM 8976 Pro (SnapDragon 653)
Qualcomm MSM 8992 (SnapDragon 808)
Qualcomm MSM 8994 (SnapDragon 810)
Qualcomm MSM 8996 (SnapDragon 820)
Qualcomm MSM 8996 Pro (SnapDragon 821)
Qualcomm MSM 8998 (SnapDragon 835)
- Main
FH Protocol updated and revised
Core revised, no more stuck boot problems
MSM8953 Pro new revision supported
MSM8905 supported
MSM8609 supported
Test support: SDM660
Test support: SDM630
- Flasher
SafeRegions detection improved
Factory firmware handling optimized
- More Secure and Generic types supported
+50 UNIQUE loaders included in internal DB!
Now QLM cover 230+ UNIQUE SECURE AND GENERIC TYPES! As nobody else
Software DO NOT require any kind of manual loaders selection, bruteforce etc.
MSM8909: ZTE, Asus, Alcatel and some Oppo
MSM8916: Coolpad, Alcatel and some Oppo
MSM8976: Vivo and others
MSM8953: Vivo and others
MSM8956: Generic Secure Chinese types, Alcatel, Lenovo and some others
MSM8936: Cover more Cyanogen based models ( include WileyFox and some rest )
MSM8937: Asus and other secure types
MSM8998: Nokia 8, and other Xiaomi models
MSM8905: Generic, LYF and other secure types
- Service operations improved
Enabled QCN operations
- Allow read calibrations and secure memory in XQCN format
- Allow write calibrations and security memory in XQCN format
- QCN verify, automatic security field update
Enabled Security repair feature
- Default "Clean memory mode" for start. Use with backup, wipe and restore
Basic DiagInfo reading during Diag operations
ADB layer activated
Enable Diag mode option released
- Allow enable diagnostic port on device [ ROOT REQUIRED! ]
- Firmware Reader engine updated
A/B memory architecture supported - allow read FW from newer devices with Android A/B update system!
New types supported ( brand-specific and generic types )
Files verification revised
-> Unlike other "solutions" CM2 make FIRMWARE BUT NOT A USELESS PLAIN DUMP ( i.e. cloning )
-> That means all device unique data, security etc. will remain safe after flashing !
- MemoryTool updated
Optimized WIPE operations
Fixed some VCL errors on Win7
BootConfigaration revised
- Other
DataDirect engine updated
Loader database updated
- 50+ new secure loaders
- Updated old and generic loaders
Some other improvements and fixes
Better UFS memory details logging
- Notes
-> Nokia QLM: since Nokia use own format of security and memory/ota structure - for COMPLETE service you should use BEST!
QLM offer basic support: FRP, Reset, Identify and backup features
-> Special THANKS to ALL our users who help us with sending reports, reporting problems and bugs, help with files and other things !
-
Support
- Posts: 4184
- Joined: 19 Oct 2011, 20:27
- Contact:
Re: Software Updates and News
iosFileUploader v1.07 released
- upload process improved
- libraries updated
- .tar and .gz files upload allowed
- minor bugs fixed
- upload process improved
- libraries updated
- .tar and .gz files upload allowed
- minor bugs fixed
-
Support
- Posts: 4184
- Joined: 19 Oct 2011, 20:27
- Contact:
Re: Software Updates and News
Infinity-Box Chinese Miracle II SCR v1.02: New models and features
Supported CPU list:
Spreadtrum: SC6530, SC6531, SC6531(A/C), SC6531E, SC6533, SC6533G
RDA Mirco: RDA8851 rev A,B,C,L,CL
RDA Micro: RDA8826
Spreadtrum SC6533/G:
Protocol updated
Revised Repair security feature (fix 000.....00 problem correctly)
- In case of problems - user MUST update FACTORY area!
FW reading revised
Identify now work faster
Identify now show much info, as possible on most models
Updated LOD tools ( flashing / customizing )
Spreadtrum SC6530/6531/A/C/E:
Revised Repair security feature
- Allow repair 3rd security field
Format FileSystem feature updated
User code read revised
Internal loaders updated
Spreadtrum other:
Protocol updated
PAC handling revised
Improved Flashing procedure for SIGNED devices
Customization for some 77xx line fixed
Supported CPU list:
Spreadtrum: SC6530, SC6531, SC6531(A/C), SC6531E, SC6533, SC6533G
RDA Mirco: RDA8851 rev A,B,C,L,CL
RDA Micro: RDA8826
Spreadtrum SC6533/G:
Protocol updated
Revised Repair security feature (fix 000.....00 problem correctly)
- In case of problems - user MUST update FACTORY area!
FW reading revised
Identify now work faster
Identify now show much info, as possible on most models
Updated LOD tools ( flashing / customizing )
Spreadtrum SC6530/6531/A/C/E:
Revised Repair security feature
- Allow repair 3rd security field
Format FileSystem feature updated
User code read revised
Internal loaders updated
Spreadtrum other:
Protocol updated
PAC handling revised
Improved Flashing procedure for SIGNED devices
Customization for some 77xx line fixed
-
Support
- Posts: 4184
- Joined: 19 Oct 2011, 20:27
- Contact:
Re: Software Updates and News
Infinity `SM` software v1.09 released
Service: adeded function Read Codes from spreadrum based phones. Androd version 5.x.x.x and lower
UserData: adeded function extract contacts to vcf via server (need internet connections) for brocken phones (work on any Android-based phones with TWRP recovery)
Installer has two parts:
- InfinityBox_install_SM_v1.09
- InfinityBox_update_SM_ResourcePack_v1.09
both parts should be installed to make new functions working !
https://www.infinity-box.com/news/?r=1216
Service: adeded function Read Codes from spreadrum based phones. Androd version 5.x.x.x and lower
UserData: adeded function extract contacts to vcf via server (need internet connections) for brocken phones (work on any Android-based phones with TWRP recovery)
Installer has two parts:
- InfinityBox_install_SM_v1.09
- InfinityBox_update_SM_ResourcePack_v1.09
both parts should be installed to make new functions working !
https://www.infinity-box.com/news/?r=1216
-
Support
- Posts: 4184
- Joined: 19 Oct 2011, 20:27
- Contact:
Re: Software Updates and News
Infinity `SM` software v1.10 released
Service - added Restore EFS via ADB (All model. Need Root)
UserData - added read Calendar (Need TWRP)
Installer has two parts:
- InfinityBox_install_SM_v1.10
- InfinityBox_update_SM_ResourcePack_v1.09 (old one). If you have Resource Pack installed earlier you do not need to download and install it again
https://www.infinity-box.com/news/?r=1217
Service - added Restore EFS via ADB (All model. Need Root)
UserData - added read Calendar (Need TWRP)
Installer has two parts:
- InfinityBox_install_SM_v1.10
- InfinityBox_update_SM_ResourcePack_v1.09 (old one). If you have Resource Pack installed earlier you do not need to download and install it again
https://www.infinity-box.com/news/?r=1217
-
Support
- Posts: 4184
- Joined: 19 Oct 2011, 20:27
- Contact:
Re: Software Updates and News
Infinity `SM` software v1.11 released
Service - added Read CRT function for MTK based phones (need Root)
Service - added Bacup SEC function for MTK based phones (need Root)
Installer has two parts:
- InfinityBox_install_SM_v1.11
- InfinityBox_update_SM_ResourcePack_v1.09 (old one). If you have Resource Pack installed earlier you do not need to download and install it again
https://www.infinity-box.com/news/?r=1218
Service - added Read CRT function for MTK based phones (need Root)
Service - added Bacup SEC function for MTK based phones (need Root)
Installer has two parts:
- InfinityBox_install_SM_v1.11
- InfinityBox_update_SM_ResourcePack_v1.09 (old one). If you have Resource Pack installed earlier you do not need to download and install it again
https://www.infinity-box.com/news/?r=1218
-
Support
- Posts: 4184
- Joined: 19 Oct 2011, 20:27
- Contact:
Re: Software Updates and News
Infinity-Box BEST NK2 v1.03
ATTENTION: To use this software you should copy licence file license_xxxxxxxx.dat from /BEST/ folder to /BEST2/ folder
- Nokia 8 line changes
New restore database for latest firmwares ( up to 439x version )
Revised flashing core
Activated ability to mirror FW version to both partition and select one of them to boot
During Identify now shown A/B SW version info
Other repair features, specified for NK8 Line only, activated
- Other
Fixed flashing issues for devices with different FlashIC sizes
Flashing core revised
More info shown during identify ( EDL/FB )
Change FW naming during reading to SW version info ( factory-like format )
Encryption state during identify revert back, since some models have NON-encrypted FileSystem
Repair Security updated
Info:
- Use Nokia Care Emergency drivers ( same as for Lumia/NXP )
- Latest available firmwares with OLD sec upload to support ( Nokia 2, Nokia 8, Nokia 5 )
- Nokia Android 8 (Oreo) changes :
> From January/February security patches EDL cables NOT work anymore on Nokia 5 and Nokia 6 !
> Security workaround, used before For Nokia 2 and Nokia 8 NOT work with new BootLoader versions!
> When new workaround will be finished, there is left for now just TP ( with device disassembly ) or rare OTA bugs to force EDL/Downgrade bootchain
https://www.infinity-box.com/news/?r=1219
ATTENTION: To use this software you should copy licence file license_xxxxxxxx.dat from /BEST/ folder to /BEST2/ folder
- Nokia 8 line changes
New restore database for latest firmwares ( up to 439x version )
Revised flashing core
Activated ability to mirror FW version to both partition and select one of them to boot
During Identify now shown A/B SW version info
Other repair features, specified for NK8 Line only, activated
- Other
Fixed flashing issues for devices with different FlashIC sizes
Flashing core revised
More info shown during identify ( EDL/FB )
Change FW naming during reading to SW version info ( factory-like format )
Encryption state during identify revert back, since some models have NON-encrypted FileSystem
Repair Security updated
Info:
- Use Nokia Care Emergency drivers ( same as for Lumia/NXP )
- Latest available firmwares with OLD sec upload to support ( Nokia 2, Nokia 8, Nokia 5 )
- Nokia Android 8 (Oreo) changes :
> From January/February security patches EDL cables NOT work anymore on Nokia 5 and Nokia 6 !
> Security workaround, used before For Nokia 2 and Nokia 8 NOT work with new BootLoader versions!
> When new workaround will be finished, there is left for now just TP ( with device disassembly ) or rare OTA bugs to force EDL/Downgrade bootchain
https://www.infinity-box.com/news/?r=1219
-
Support
- Posts: 4184
- Joined: 19 Oct 2011, 20:27
- Contact:
Re: Software Updates and News
Chinese Miracle-2 MTK/Mediatek v2.00 - new CPU support, new features, new options
MTK 6570 CPU support:
with NAND memory
with eMMC memory
Read Info - Complete device info, Security info
Read Firmware - Factory Scatter format [ NAND supported - WorldFirst and unique! ]
Write Firmware - Factory Scatter Format [ NAND supported - WorldFirst and unique! ]
Read NVRAM
Write NVRAM
Repair Security
Formay FS - FRP, Settings, Privacy ( and mixed/special mode )
MemoryTool
MTK 6750 CPU support:
Read Info - Complete device info, Security info
Read Firmware
Write Firmware
Read NVRAM
Write NVRAM
Repair Security
Formay FS - FRP, Settings, Privacy ( and mixed/special mode )
MemoryTool
MTK 6755 CPU support:
Read Info - Complete device info, Security info
Read Firmware
Write Firmware
Read NVRAM
Write NVRAM
Repair Security
Formay FS - FRP, Settings, Privacy ( and mixed/special mode )
MemoryTool
MTK 6757 CPU support:
Read Info - Complete device info, Security info
Read Firmware
Write Firmware
Read NVRAM
Write NVRAM
Repair Security
Formay FS - FRP, Settings, Privacy ( and mixed/special mode )
MemoryTool
MTK 6763 CPU support:
Read Info - Complete device info, Security info
Read Firmware
Write Firmware
Read NVRAM
Write NVRAM
Repair Security
Formay FS - FRP, Settings, Privacy ( and mixed/special mode )
MemoryTool
MTK 6797 CPU support:
Read Info - Complete device info, Security info
Read Firmware
Write Firmware
Read NVRAM
Write NVRAM
Repair Security
Formay FS - FRP, Settings, Privacy ( and mixed/special mode )
MemoryTool
--- Under Test ---
MTK 6758 CPU support:
Read Info - Complete device info, Security info
Read Firmware
Write Firmware
Read NVRAM
Write NVRAM
Repair Security
Formay FS - FRP, Settings, Privacy ( and mixed/special mode )
MemoryTool
MTK 6739 CPU support:
with NAND memory
with eMMC memory
Read Info - Complete device info, Security info
Read Firmware
Write Firmware
Read NVRAM
Write NVRAM
Repair Security
Formay FS - FRP, Settings, Privacy ( and mixed/special mode )
MemoryTool
Main
- New look and design. All simplified and optimized much, as possible. [ please refer to v2 interface introduction ]
- New core. All code made from scratch.
- New boot chain selection mode - automatic ( via defined user combination ) or manual.
- New connection
- Complete error handling and explanation
- Internal EMIDB cover 99% of existing memory devices on both - NAND and eMMC devices
- Easy end user customization for adding support for new device etc.
Flasher
- Completely new flasher design, which allow customize whole flashing process [ please refer to v2 interface introduction ]
FW Reader
- Completely new core, which allow handle all existing types and flash devices.
Service
- Security repair NOT require reboot to meta, not required CDC drivers or whatever else. All direct.
- Format FS include different mode, optimized for different secure devices type ( with FORMAT, WRITE protection )
- During NVRAM read/write SW also verify it condition and data
MEMORY TOOL activated!
Easy, fast and ultimate solution now come in MTK too!
- Support eMMC and NAND flash IC secure
- Allow READ, WRITE, ERASE partitions
- Show partitions states and info only for eMMC devices
- Allow RE-init PMT ( from scatter )
Other
Lot of other changes from v1 line, which not mandatory to mention
Known issues/warnings/info:
1. [NAND on MT6570] v1712, v1736 loader packages NOT SHOULD BE USED! Since they have ftl/ecc errors!
In result you will give read/write FW errors and rest problems at all.
Recommend use v1724 for FACTORY FW flashing, v18xx line for Infinity FW Flash Read and Write
2. [NAND on MT6570] In some cases "stuck on logo" devices can be fixed only via FFU (whole flash) format!
1. [NAND on MT6570] UBI SPARSE image flashing may take MUCH time (up to 5 minutes and more) for some devices!
3. [MEMORY TOOL] Partitions state on MEMORY TOOL will be empty in MT6570 NAND phones, it is normal and cannot be fixed.
Read-write data, which you want, ignore "EMPTY" states.
4. [MEMORY TOOL] Old protocol secure devices (MT6750/MT6755) - LeEco and similar
In some cases WIPE partition may not work!
5. ADL checksum MAY NOT WORK CORRECT on MT6570 NAND/eMMC devices! Result - stuck after system/userdata partition flashing
6. FileSyhstems flashing on some SBC-enabled devices ( except SYSTEM/CACHE/USER ) may fail! Solution - exclude them from flashing list.
7. Device with NV_TYPE2 security may not work yet for repair sec!
Note:
- You DO NOT need to update Smart-Card to use this version. Smart-Card firmware v0136 is enough to use this version
- Software installed to new folder /CM2MT2/ and designed to support new models
- DO NOT uninstall previous version 1.58, in some cases you still need it
- If you are trying to connect phone with new software and see a message like LEGACY MTK - please use version 1.58 for this device !
- Some unpredictable bugs have been found with some PC and OS configurations, it may lead to "Access violation..." errors. Problem is known and fix is on the way.
https://www.infinity-box.com/news/?r=1225
MTK 6570 CPU support:
with NAND memory
with eMMC memory
Read Info - Complete device info, Security info
Read Firmware - Factory Scatter format [ NAND supported - WorldFirst and unique! ]
Write Firmware - Factory Scatter Format [ NAND supported - WorldFirst and unique! ]
Read NVRAM
Write NVRAM
Repair Security
Formay FS - FRP, Settings, Privacy ( and mixed/special mode )
MemoryTool
MTK 6750 CPU support:
Read Info - Complete device info, Security info
Read Firmware
Write Firmware
Read NVRAM
Write NVRAM
Repair Security
Formay FS - FRP, Settings, Privacy ( and mixed/special mode )
MemoryTool
MTK 6755 CPU support:
Read Info - Complete device info, Security info
Read Firmware
Write Firmware
Read NVRAM
Write NVRAM
Repair Security
Formay FS - FRP, Settings, Privacy ( and mixed/special mode )
MemoryTool
MTK 6757 CPU support:
Read Info - Complete device info, Security info
Read Firmware
Write Firmware
Read NVRAM
Write NVRAM
Repair Security
Formay FS - FRP, Settings, Privacy ( and mixed/special mode )
MemoryTool
MTK 6763 CPU support:
Read Info - Complete device info, Security info
Read Firmware
Write Firmware
Read NVRAM
Write NVRAM
Repair Security
Formay FS - FRP, Settings, Privacy ( and mixed/special mode )
MemoryTool
MTK 6797 CPU support:
Read Info - Complete device info, Security info
Read Firmware
Write Firmware
Read NVRAM
Write NVRAM
Repair Security
Formay FS - FRP, Settings, Privacy ( and mixed/special mode )
MemoryTool
--- Under Test ---
MTK 6758 CPU support:
Read Info - Complete device info, Security info
Read Firmware
Write Firmware
Read NVRAM
Write NVRAM
Repair Security
Formay FS - FRP, Settings, Privacy ( and mixed/special mode )
MemoryTool
MTK 6739 CPU support:
with NAND memory
with eMMC memory
Read Info - Complete device info, Security info
Read Firmware
Write Firmware
Read NVRAM
Write NVRAM
Repair Security
Formay FS - FRP, Settings, Privacy ( and mixed/special mode )
MemoryTool
Main
- New look and design. All simplified and optimized much, as possible. [ please refer to v2 interface introduction ]
- New core. All code made from scratch.
- New boot chain selection mode - automatic ( via defined user combination ) or manual.
- New connection
- Complete error handling and explanation
- Internal EMIDB cover 99% of existing memory devices on both - NAND and eMMC devices
- Easy end user customization for adding support for new device etc.
Flasher
- Completely new flasher design, which allow customize whole flashing process [ please refer to v2 interface introduction ]
FW Reader
- Completely new core, which allow handle all existing types and flash devices.
Service
- Security repair NOT require reboot to meta, not required CDC drivers or whatever else. All direct.
- Format FS include different mode, optimized for different secure devices type ( with FORMAT, WRITE protection )
- During NVRAM read/write SW also verify it condition and data
MEMORY TOOL activated!
Easy, fast and ultimate solution now come in MTK too!
- Support eMMC and NAND flash IC secure
- Allow READ, WRITE, ERASE partitions
- Show partitions states and info only for eMMC devices
- Allow RE-init PMT ( from scatter )
Other
Lot of other changes from v1 line, which not mandatory to mention
Known issues/warnings/info:
1. [NAND on MT6570] v1712, v1736 loader packages NOT SHOULD BE USED! Since they have ftl/ecc errors!
In result you will give read/write FW errors and rest problems at all.
Recommend use v1724 for FACTORY FW flashing, v18xx line for Infinity FW Flash Read and Write
2. [NAND on MT6570] In some cases "stuck on logo" devices can be fixed only via FFU (whole flash) format!
1. [NAND on MT6570] UBI SPARSE image flashing may take MUCH time (up to 5 minutes and more) for some devices!
3. [MEMORY TOOL] Partitions state on MEMORY TOOL will be empty in MT6570 NAND phones, it is normal and cannot be fixed.
Read-write data, which you want, ignore "EMPTY" states.
4. [MEMORY TOOL] Old protocol secure devices (MT6750/MT6755) - LeEco and similar
In some cases WIPE partition may not work!
5. ADL checksum MAY NOT WORK CORRECT on MT6570 NAND/eMMC devices! Result - stuck after system/userdata partition flashing
6. FileSyhstems flashing on some SBC-enabled devices ( except SYSTEM/CACHE/USER ) may fail! Solution - exclude them from flashing list.
7. Device with NV_TYPE2 security may not work yet for repair sec!
Note:
- You DO NOT need to update Smart-Card to use this version. Smart-Card firmware v0136 is enough to use this version
- Software installed to new folder /CM2MT2/ and designed to support new models
- DO NOT uninstall previous version 1.58, in some cases you still need it
- If you are trying to connect phone with new software and see a message like LEGACY MTK - please use version 1.58 for this device !
- Some unpredictable bugs have been found with some PC and OS configurations, it may lead to "Access violation..." errors. Problem is known and fix is on the way.
https://www.infinity-box.com/news/?r=1225
-
Support
- Posts: 4184
- Joined: 19 Oct 2011, 20:27
- Contact:
Re: Software Updates and News
Chinese Miracle-2 MTK/Mediatek v2.00 r2 - MT6739 support, SPUnlock and more
- Main
MT6739 CPU supported!
MT6739 moved from TEST to GENERAL support.
Firmwware read
Firmware write
NVRAM read
NVRAM write
Reset Settings / Format FS
Reset FRP
Reset Privacy
MemoryTool
- MemoryTool
Fixed PMT init on some devices
Optimized Expand/Collapse view functions
Fixed DA1804 and DA1712 loaders support for WIPE
Optimized NAND support
- Service
NVRAM module updated
.dynamic page detection
.some types support fixed
.repair security ( security type detection ) updated
FormatFS / Reset settings rebuild
.Activated fully automatic "FULL FACTORY" mode, designed for all modern devices ( include devices with SEC_CONTROL )
."FULL FACTORY" mode set to default
.Some "OLD" agents (DA15xx) may not work
- SP Unlock activated
Support all MTK modern phones, except MT6763 and MT6739.
Read codes and Direct Unlock mode supported
MT6570 eMMC ONLY devices supported
- Core
Fixed memory leak issues and problems with booting on some systems
Optimized different OLD agents support for MODERN devices ( DA16xx and DA17xx line )
SW more faster now
EMI handler for MT6570 and MT6797 fully automated and complete
Improved EMI lookup support for MT675x devices
EMIDB updated
Hint/Error explain module updated
MT6758 support under test
MT6771 support under test
- Flasher
Fixed break issue, when just one file selected for flashing.
HWInfo compatibility status shown in log in both cases ( succes or failed )
- FW reader
MT6739 support
New types of firmwares supported
Optimized NAND reading on DA18xx line loaders
Read Firmware size now shown in log
- New models included
Limited MEIZU support
Limited Oppo support
Limited Gionee support
Limited BQ support
Some basic "generic" secure devices support optimized
Known issues/warnings/info :
1. [NAND on MT6570] v1712,v1736 loader packages NOT SHOULD BE USED! Since they have ftl/ecc errors!
In result you will give read/write FW errors and rest problems at all.
Recommend use v1724 for FACTORY FW flashing, v18xx line for Infinity FW Flash Read and Write
2. [NAND on MT6570] In some cases "stuck on logo" devices can be fixed only via FFU (whole flash) format!
3. [MEMORY TOOL] Partitions state on MEMORY TOOL will be empty in MT6570 NAND phones, it is normal and cannot be fixed.
Read-Write data, which you want, ignore "EMPTY" states.
4. ADL checksum MAY NOT WORK CORRECT on MT6570 NAND devices! Result - stuck after system/userdata partition flashing
5. FileSystem flashing on some SBC-enabled devices ( except SYSTEM/CACHE/USER ) may fail! Solution - exclude them from flashing list.
6. Cheap MT6739 devices require BATTERY REMOVING after EVERY operation in most cases!
7. Meizu support is limited by Preloader Level ( No BROM SLA ) - you must UNTICK "PMT Update" and "PRELOADER" partition from flashing list!
https://www.infinity-box.com/support/?r=100002
- Main
MT6739 CPU supported!
MT6739 moved from TEST to GENERAL support.
Firmwware read
Firmware write
NVRAM read
NVRAM write
Reset Settings / Format FS
Reset FRP
Reset Privacy
MemoryTool
- MemoryTool
Fixed PMT init on some devices
Optimized Expand/Collapse view functions
Fixed DA1804 and DA1712 loaders support for WIPE
Optimized NAND support
- Service
NVRAM module updated
.dynamic page detection
.some types support fixed
.repair security ( security type detection ) updated
FormatFS / Reset settings rebuild
.Activated fully automatic "FULL FACTORY" mode, designed for all modern devices ( include devices with SEC_CONTROL )
."FULL FACTORY" mode set to default
.Some "OLD" agents (DA15xx) may not work
- SP Unlock activated
Support all MTK modern phones, except MT6763 and MT6739.
Read codes and Direct Unlock mode supported
MT6570 eMMC ONLY devices supported
- Core
Fixed memory leak issues and problems with booting on some systems
Optimized different OLD agents support for MODERN devices ( DA16xx and DA17xx line )
SW more faster now
EMI handler for MT6570 and MT6797 fully automated and complete
Improved EMI lookup support for MT675x devices
EMIDB updated
Hint/Error explain module updated
MT6758 support under test
MT6771 support under test
- Flasher
Fixed break issue, when just one file selected for flashing.
HWInfo compatibility status shown in log in both cases ( succes or failed )
- FW reader
MT6739 support
New types of firmwares supported
Optimized NAND reading on DA18xx line loaders
Read Firmware size now shown in log
- New models included
Limited MEIZU support
Limited Oppo support
Limited Gionee support
Limited BQ support
Some basic "generic" secure devices support optimized
Known issues/warnings/info :
1. [NAND on MT6570] v1712,v1736 loader packages NOT SHOULD BE USED! Since they have ftl/ecc errors!
In result you will give read/write FW errors and rest problems at all.
Recommend use v1724 for FACTORY FW flashing, v18xx line for Infinity FW Flash Read and Write
2. [NAND on MT6570] In some cases "stuck on logo" devices can be fixed only via FFU (whole flash) format!
3. [MEMORY TOOL] Partitions state on MEMORY TOOL will be empty in MT6570 NAND phones, it is normal and cannot be fixed.
Read-Write data, which you want, ignore "EMPTY" states.
4. ADL checksum MAY NOT WORK CORRECT on MT6570 NAND devices! Result - stuck after system/userdata partition flashing
5. FileSystem flashing on some SBC-enabled devices ( except SYSTEM/CACHE/USER ) may fail! Solution - exclude them from flashing list.
6. Cheap MT6739 devices require BATTERY REMOVING after EVERY operation in most cases!
7. Meizu support is limited by Preloader Level ( No BROM SLA ) - you must UNTICK "PMT Update" and "PRELOADER" partition from flashing list!
https://www.infinity-box.com/support/?r=100002
-
Support
- Posts: 4184
- Joined: 19 Oct 2011, 20:27
- Contact:
Re: Software Updates and News
Chinese Miracle-2 MTK/Mediatek v2.00 r3 - More secured devices and features !
Important information:
- You DO NOT need to update Smart-Card to use this version. Smart-Card firmware v0136 is enough to use this version
- DO NOT uninstall previous version 1.58, in some cases you still need it
- Software installed to new folder /CM2MT2/ and designed to support new models
- If you are trying to connect phone with new software and see a message like LEGACY MTK - please use version 1.58 for this device !
- Main
DownloadAgent version 1816 supported and tested on all supported SoC.
Fixed some memory leaks
Connection level revised
- MemoryTool
Fixed multi-selection
GPT init revised
Preloader init revised
- Service
Repair Security revised. Fixed issues with some Meizu and other models.
- Core
Optimized different agents versions support ( DA16xx line )
EMIDB updated
Hint/Error explain module updated
Activated SymLinks - allow reduce boot base size by redirecting diffirent brand/models if they have same base
BootHelper ( stage 1 of 3 ) activated - hints/explanation of boot sequnce and correct file selection
MT6758 support under test
MT6771 support under test
MT6765 support under test
- Flasher
Show Preloader HW compatibility when load firmware in flash tab
Fixed file selection order - if SW package contain mixed types - secure will be selected by default
- FW reader
New types of firmwares supported
Scatter creation optimized for some SoC
- New models included
Limited Alcatel support
Limited Gionee support
Limited Wiko support
Limited Tecno support
And diffirent other models
Some other basic "generic" secure devices support optimized
NAND devices on MT6570 moved to separate mode ( under base ) - FACTORY for ONLY FACTORY-provided FW flashing, INFINITY - for all rest operations
Known issues/warnings/info :
1. [NAND on MT6570] v1712,v1736 loader packages NOT SHOULD BE USED! Since they have ftl/ecc errors!
In result you will give read/write FW errors and rest problems at all.
Recommend use v1724 for FACTORY FW flashing, v18xx line for Infinity FW Flash Read and Write
2. [NAND on MT6570] In some cases "stuck on logo" devices can be fixed only via FFU (whole flash) format!
3. [MEMORY TOOL] Partitions state on MEMORY TOOL will be empty in MT6570 NAND phones, it is normal and cannot be fixed.
Read-Write data, which you want, ignore "EMPTY" states.
4. ADL checksum MAY NOT WORK CORRECT on MT6570 NAND devices! Result - stuck after system/userdata partition flashing
5. FileSystem flashing on some SBC-enabled devices ( except SYSTEM/CACHE/USER ) may fail! Solution - exclude them from flashing list.
6. Cheap MT6739 devices require BATTERY REMOVING after EVERY operation in most cases!
7. Meizu support is limited by Preloader Level ( No BROM SLA ) - you must UNTICK "PMT Update" and "PRELOADER" partition from flashing list!
8. [NAND on MT6570] In some cases device MAY DEAD after flashing! Make sure you have TESTED firmware version!
If you have download FW from internet/other source - make sure it preloader CONTAIN 3 EMI record! Preloader jc45btlc with 2 records KILL SOME DEVICE TO UNRECOVERABLE STATE!!!
Preloader info shown now during FW load.
Credits :
gracy_elec - different useful files contribution
kamal_singla - testing and useful files contribution
merujeffrey - useful files contribution and report logs
https://www.infinity-box.com/support/?r=100006
Important information:
- You DO NOT need to update Smart-Card to use this version. Smart-Card firmware v0136 is enough to use this version
- DO NOT uninstall previous version 1.58, in some cases you still need it
- Software installed to new folder /CM2MT2/ and designed to support new models
- If you are trying to connect phone with new software and see a message like LEGACY MTK - please use version 1.58 for this device !
- Main
DownloadAgent version 1816 supported and tested on all supported SoC.
Fixed some memory leaks
Connection level revised
- MemoryTool
Fixed multi-selection
GPT init revised
Preloader init revised
- Service
Repair Security revised. Fixed issues with some Meizu and other models.
- Core
Optimized different agents versions support ( DA16xx line )
EMIDB updated
Hint/Error explain module updated
Activated SymLinks - allow reduce boot base size by redirecting diffirent brand/models if they have same base
BootHelper ( stage 1 of 3 ) activated - hints/explanation of boot sequnce and correct file selection
MT6758 support under test
MT6771 support under test
MT6765 support under test
- Flasher
Show Preloader HW compatibility when load firmware in flash tab
Fixed file selection order - if SW package contain mixed types - secure will be selected by default
- FW reader
New types of firmwares supported
Scatter creation optimized for some SoC
- New models included
Limited Alcatel support
Limited Gionee support
Limited Wiko support
Limited Tecno support
And diffirent other models
Some other basic "generic" secure devices support optimized
NAND devices on MT6570 moved to separate mode ( under base ) - FACTORY for ONLY FACTORY-provided FW flashing, INFINITY - for all rest operations
Known issues/warnings/info :
1. [NAND on MT6570] v1712,v1736 loader packages NOT SHOULD BE USED! Since they have ftl/ecc errors!
In result you will give read/write FW errors and rest problems at all.
Recommend use v1724 for FACTORY FW flashing, v18xx line for Infinity FW Flash Read and Write
2. [NAND on MT6570] In some cases "stuck on logo" devices can be fixed only via FFU (whole flash) format!
3. [MEMORY TOOL] Partitions state on MEMORY TOOL will be empty in MT6570 NAND phones, it is normal and cannot be fixed.
Read-Write data, which you want, ignore "EMPTY" states.
4. ADL checksum MAY NOT WORK CORRECT on MT6570 NAND devices! Result - stuck after system/userdata partition flashing
5. FileSystem flashing on some SBC-enabled devices ( except SYSTEM/CACHE/USER ) may fail! Solution - exclude them from flashing list.
6. Cheap MT6739 devices require BATTERY REMOVING after EVERY operation in most cases!
7. Meizu support is limited by Preloader Level ( No BROM SLA ) - you must UNTICK "PMT Update" and "PRELOADER" partition from flashing list!
8. [NAND on MT6570] In some cases device MAY DEAD after flashing! Make sure you have TESTED firmware version!
If you have download FW from internet/other source - make sure it preloader CONTAIN 3 EMI record! Preloader jc45btlc with 2 records KILL SOME DEVICE TO UNRECOVERABLE STATE!!!
Preloader info shown now during FW load.
Credits :
gracy_elec - different useful files contribution
kamal_singla - testing and useful files contribution
merujeffrey - useful files contribution and report logs
https://www.infinity-box.com/support/?r=100006
-
Support
- Posts: 4184
- Joined: 19 Oct 2011, 20:27
- Contact:
Re: Software Updates and News
Infinity Chinese Miracle-2 MTK/Mediatek v2.00 r4 - MT6771 support and other features !
Important:
- Software installed to new folder /CM2MT2/ and designed to support new models
- Smart-Card firmware v0136 is Ok to use this version
- DO NOT uninstall previous version 1.58 ! If you are trying to connect phone with new software and see a message like LEGACY MTK you should use version 1.58 for this device !
- Main
Connection level revised
BROM level support optimized
MT6771 CPU supported!
MT6771 moved from TEST to GENERAL support.
Firmwware read
Firmware write
NVRAM read
NVRAM write
Reset Settings / Format FS
Reset FRP
Reset Privacy
MemoryTool
- Service
Repair Security revised. Fixed issues with some NV types.
- Core
EMIDB updated
Hint/Error explain module updated
MT6758 support under test
MT6765 support under test
- FW reader
MT6771 supported
New types of firmwares supported
Scatter creation optimized
- SP Unlock
Revised unlock support for some models
Info: MT6739/MT6763/MT6771 IS NOT supported YET!
- New models included
Limited Oppo support (F7/A3)
Limited Vivo support
And diffirent other models
Some other basic "generic" secure devices support optimized
Known issues/warnings/info:
1. [NAND on MT6570] v1712, v1736 loader packages SHOULD NOT BE USED due to these packages have ftl/ecc errors!
In result you will give read/write FW errors and rest problems at all.
Recommend use v1724 for FACTORY FW flashing, v18xx line for Infinity FW Flash Read and Write
2. [NAND on MT6570] In some cases "stuck on logo" devices can be fixed only via FFU (whole flash) format!
3. [MEMORY TOOL] Partitions state on MEMORY TOOL will be empty in MT6570 NAND phones, it is normal behaviour and can not be fixed.
Read-Write data, which you want, ignore "EMPTY" states.
4. ADL checksum MAY NOT WORK CORRECT on MT6570 NAND devices! Result - stuck after system/userdata partition flashing
5. FileSystem flashing on some SBC-enabled devices (except SYSTEM/CACHE/USER) may fail ! Solution - exclude them from flashing list.
6. Cheap MT6739 devices require BATTERY REMOVING after EVERY operation in most cases !
7. Meizu support is limited by Preloader Level ( No BROM SLA ) - you must UNTICK "PMT Update" and "PRELOADER" partition from flashing list!
8. [NAND on MT6570] In some cases device MAY BE DEAD after flashing! Make sure you have TESTED firmware version!
If you have download FW from internet/other source - make sure it preloader CONTAIN 3 EMI record! Preloader jc45btlc with 2 records KILL SOME DEVICE TO UNRECOVERABLE STATE !
Preloader info shown now during FW load.
Credits :
kamal_singla - testing and useful files contribution
https://www.infinity-box.com/support/?r=100016
Important:
- Software installed to new folder /CM2MT2/ and designed to support new models
- Smart-Card firmware v0136 is Ok to use this version
- DO NOT uninstall previous version 1.58 ! If you are trying to connect phone with new software and see a message like LEGACY MTK you should use version 1.58 for this device !
- Main
Connection level revised
BROM level support optimized
MT6771 CPU supported!
MT6771 moved from TEST to GENERAL support.
Firmwware read
Firmware write
NVRAM read
NVRAM write
Reset Settings / Format FS
Reset FRP
Reset Privacy
MemoryTool
- Service
Repair Security revised. Fixed issues with some NV types.
- Core
EMIDB updated
Hint/Error explain module updated
MT6758 support under test
MT6765 support under test
- FW reader
MT6771 supported
New types of firmwares supported
Scatter creation optimized
- SP Unlock
Revised unlock support for some models
Info: MT6739/MT6763/MT6771 IS NOT supported YET!
- New models included
Limited Oppo support (F7/A3)
Limited Vivo support
And diffirent other models
Some other basic "generic" secure devices support optimized
Known issues/warnings/info:
1. [NAND on MT6570] v1712, v1736 loader packages SHOULD NOT BE USED due to these packages have ftl/ecc errors!
In result you will give read/write FW errors and rest problems at all.
Recommend use v1724 for FACTORY FW flashing, v18xx line for Infinity FW Flash Read and Write
2. [NAND on MT6570] In some cases "stuck on logo" devices can be fixed only via FFU (whole flash) format!
3. [MEMORY TOOL] Partitions state on MEMORY TOOL will be empty in MT6570 NAND phones, it is normal behaviour and can not be fixed.
Read-Write data, which you want, ignore "EMPTY" states.
4. ADL checksum MAY NOT WORK CORRECT on MT6570 NAND devices! Result - stuck after system/userdata partition flashing
5. FileSystem flashing on some SBC-enabled devices (except SYSTEM/CACHE/USER) may fail ! Solution - exclude them from flashing list.
6. Cheap MT6739 devices require BATTERY REMOVING after EVERY operation in most cases !
7. Meizu support is limited by Preloader Level ( No BROM SLA ) - you must UNTICK "PMT Update" and "PRELOADER" partition from flashing list!
8. [NAND on MT6570] In some cases device MAY BE DEAD after flashing! Make sure you have TESTED firmware version!
If you have download FW from internet/other source - make sure it preloader CONTAIN 3 EMI record! Preloader jc45btlc with 2 records KILL SOME DEVICE TO UNRECOVERABLE STATE !
Preloader info shown now during FW load.
Credits :
kamal_singla - testing and useful files contribution
https://www.infinity-box.com/support/?r=100016
-
Support
- Posts: 4184
- Joined: 19 Oct 2011, 20:27
- Contact:
Re: Software Updates and News
Infinity Chinese Miracle II SCR/SPD-RDA v1.03: New models and features
Supported CPU list:
Spreadtrum: SC6530, SC6531, SC6531(A/C), SC6531E, SC6533, SC6533G
RDA Mirco: RDA8851 rev A,B,C,L,CL
RDA Micro: RDA8826
RDA Mirco RDA8851 rev A,B,C,L,CL/RDA8826
Flashing protocol updated
Updated LOD tools ( flashing / customizing )
Spreadtrum SC6533/G:
Protocol updated
Support for REV2 bootrom mode activated
FW reading revised
Updated LOD tools ( flashing / customizing )
Spreadtrum SC6530/6531/A/C/E:
Revised Repair security feature
Flashing revised
-> Activated "Format FFS" during BINARY dump writing
-> Use that feature, if device not allow make direct format ( some C/E revision devices )
User code read revised - activated 2nd mode : from DUMP
-> Press and hold LEFT SHIFT key, while starting ReadUsercode code operation. Select desired dump file to read code.
Activated AUTO fixer for memory dumps
Internal loaders updated
Spreadtrum other:
Protocol updated
PAC handling revised
Improved Flashing procedure for SC7701/SC7702 devices
Improved Flashing procedure for SC6825/SC8825 devices
Known issues[*]/warnings[!]/info:
1. AUTO fixer for memory dumps
-> That feature will AUTOMATICALLY FIX dumps from devices with "abnormal" flash and memory layout ( issue found on number of devices 16MB flash with 8MB layout )
-> Just select binary dump in flashing tab or any other operation, which require file select.
2. [*] In some cases Format FFS may fail on E and C rev
-> Read Flash Dump, write it back. During Dump writing SW will ask you about FormatFFS.
https://www.infinity-box.com/support/?r=100019
Supported CPU list:
Spreadtrum: SC6530, SC6531, SC6531(A/C), SC6531E, SC6533, SC6533G
RDA Mirco: RDA8851 rev A,B,C,L,CL
RDA Micro: RDA8826
RDA Mirco RDA8851 rev A,B,C,L,CL/RDA8826
Flashing protocol updated
Updated LOD tools ( flashing / customizing )
Spreadtrum SC6533/G:
Protocol updated
Support for REV2 bootrom mode activated
FW reading revised
Updated LOD tools ( flashing / customizing )
Spreadtrum SC6530/6531/A/C/E:
Revised Repair security feature
Flashing revised
-> Activated "Format FFS" during BINARY dump writing
-> Use that feature, if device not allow make direct format ( some C/E revision devices )
User code read revised - activated 2nd mode : from DUMP
-> Press and hold LEFT SHIFT key, while starting ReadUsercode code operation. Select desired dump file to read code.
Activated AUTO fixer for memory dumps
Internal loaders updated
Spreadtrum other:
Protocol updated
PAC handling revised
Improved Flashing procedure for SC7701/SC7702 devices
Improved Flashing procedure for SC6825/SC8825 devices
Known issues[*]/warnings[!]/info:
1. AUTO fixer for memory dumps
-> That feature will AUTOMATICALLY FIX dumps from devices with "abnormal" flash and memory layout ( issue found on number of devices 16MB flash with 8MB layout )
-> Just select binary dump in flashing tab or any other operation, which require file select.
2. [*] In some cases Format FFS may fail on E and C rev
-> Read Flash Dump, write it back. During Dump writing SW will ask you about FormatFFS.
https://www.infinity-box.com/support/?r=100019
-
Support
- Posts: 4184
- Joined: 19 Oct 2011, 20:27
- Contact:
Re: Software Updates and News
Infinity `SM` software v2.00 released
Infinity Samsung Activation server is back with new Smart-Card firmware for latest `SM` software release.
`SM` software v1.xx was released time ago as a free software for Infinity users. From now v2.00 released as a paid addon.
Users who have made free Infinity `SM` activation can use it in future with `SM` software v1.xx. If users of free `SM` Activation want to use `SM` software v2.xx they should obtain new `SM` activation.
Infinity `SM` software v2.00 news:
- many internal stability improvements
- FRP unlock engine re-written
- FRP unlock procedure updated
- security area write for MTK based devices
- security area write for Exynos based devices
- Smart-Card firmware should be updated to use this software release
- "SM ResourcePack" should be installed to get all released functions working
At the moment there is a special offer for `SM` v2.xx Activation. Price is quite cheap right now but with each new `SM` update released price will be higher than before. So you can activate software right now for a cheap price or you can wait some time, see software updates progress and then pay higher price for it.
https://www.infinity-box.com/support/?r=100034
Infinity Samsung Activation server is back with new Smart-Card firmware for latest `SM` software release.
`SM` software v1.xx was released time ago as a free software for Infinity users. From now v2.00 released as a paid addon.
Users who have made free Infinity `SM` activation can use it in future with `SM` software v1.xx. If users of free `SM` Activation want to use `SM` software v2.xx they should obtain new `SM` activation.
Infinity `SM` software v2.00 news:
- many internal stability improvements
- FRP unlock engine re-written
- FRP unlock procedure updated
- security area write for MTK based devices
- security area write for Exynos based devices
- Smart-Card firmware should be updated to use this software release
- "SM ResourcePack" should be installed to get all released functions working
At the moment there is a special offer for `SM` v2.xx Activation. Price is quite cheap right now but with each new `SM` update released price will be higher than before. So you can activate software right now for a cheap price or you can wait some time, see software updates progress and then pay higher price for it.
https://www.infinity-box.com/support/?r=100034