Infinity Box Dongle [CM2] [BEST] Support

Infinity Nokia [BEST] v2.29 - MTK Nokia Firmware Reader/Maker and more

- MTKx Flash Engine updated
Automatic "Repair Mode" enable, if device have damaged ROM
Infinity ( Factory-Like ) FW flashing support

- xCNT tool updated
MediaTek tab activated
Allow make firmware for MTK phones from read dump

Supported lines:
Nokia 108: RM-944, RM-945, RM-1124
Nokia 220: RM-969, RM-970, RM-971, RM-1125
Nokia 225: RM-1011, RM-1012, RM-1043
Nokia 130: RM-1035, RM-1036, RM-1037, RM-1122
Nokia 215: RM-1110, RM-1111, RM-1112
Nokia 105: RM-1133, RM-1134, RM-1135
Nokia 222: RM-1136, RM-1137
Nokia 230: RM-1172, RM-1173
Nokia 216: RM-1187, RM-1188
Nokia 150: RM-1189, RM-1190

Result FW is like factory one, which contain all need part to complete reflash or langpack change.

Older models below Nokia 105 are supported as backward compatibility. Almost not required to use.
Main use:
1. Make firmwares for HMD phones which are NOT available YET!
2. MTKx Legacy/HMD models problem solution: read FW from HMD devices (sw11 and newer)
Optional use: Make firmwares with required LANGPACK which are NOT available YET!

- Service operations revised
MTKx: FlahIC detection on flash read improved for some devices
MTKx: Dump reading more faster now
NXP: HW revision verification has made problems for some rare X+ and XL+ models, fixed

- Other
Some bugfixes and improvements at all

MTKx Legacy/HMD models:
Those phones may have 2 version of firmware (old and new sec)
Nokia 150 (it has legacy and hmd version)
Nokia 105, Nokia 130, Nokia 216, Nokia 222, Nokia 230: probably two versions are available
CS problem after flashing may be a result of flashing different version. Just reflash to another one ( SW10: LEGACY, SW11 and newer: HMD )

Lumia/Nokia:
MS will CLOSE WHOLE Windows Mobile support at June 2017.
What will be with servers with firmwares - no one knows, but MS politic is simple - close and forget!
If you have chance, free drive space and good inet: DOWNLOAD ALL NEED FIRMWARES!
There will be NO newer versions anymore other than existing ones.

Infinity Chinese Miracle-2 SPD/Spreadtrum v1.26 - SC9820 support, SC983x Android 7 support and more

Activated SC9820 support - World First!
Identify (service/boot)
Read firmware ( SC/PAC )
Write Firmware ( SC/PAC )
Reset Settings/Format FS
Reset FRP
Flash erase
NVM operations: Read, Write, Clear, Fix BB
Repair Security (Normal and Flash Mode)
SP Unlock
eMMC test
HW info read/write

Activated SC983x Android 7 support
Identify (service/boot)
Read firmware ( SC/PAC )
Write Firmware ( SC/PAC )
Reset Settings/Format FS
Reset FRP
Flash erase
NVM operations: Read, Write, Clear, Fix BB
Repair Security (Normal and Flash Mode)
SP Unlock
eMMC test
HW info read/write

- Flash Engine updated
Improved SC98xx series support

- Service operations improved
NVM operations revised ( some old types support fixed )
SP unlock revised for some old SC77xx series devices
FRP reset supported for Android 7 devices

- Firmware reader updated
New types support
Android 7 (Nougat) supported

- Other
Some bugfixes and improvements at all
FlashLoader package updated

Infinity Chinese Miracle-2 QLM v1.12 - SnapDragon 820 and 821, UFS Memory support

- New CPU line activated:
SnapDragon 820: Generic, Xiaomi, Lenovo and much other devices
SnapDragon 821: Generic, Xiaomi, Lenovo and much other devices
SnapDragon 653: Generic, Alcatel, ZTE and much other devices

Supported CPU List:
Qualcomm MSM 8210 (SnapDragon 200)
Qualcomm MSM 8212 (SnapDragon 200)
Qualcomm MSM 8610 (SnapDragon 200)
Qualcomm MSM 8612 (SnapDragon 200)
Qualcomm MSM 8226 (SnapDragon 400)
Qualcomm MSM 8626 (SnapDragon 400)
Qualcomm MSM 8926 (SnapDragon 400)
Qualcomm MSM 8228 (SnapDragon 400)
Qualcomm MSM 8628 (SnapDragon 400)
Qualcomm MSM 8928 (SnapDragon 400)
Qualcomm APQ 8009 (SnapDragon 210)
Qualcomm MSM 8209 (SnapDragon 210)
Qualcomm MSM 8909 (SnapDragon 210)
Qualcomm MSM 8916 (SnapDragon 410)
Qualcomm MSM 8917 (SnapDragon 425)
Qualcomm MSM 8929 (SnapDragon 415)
Qualcomm MSM 8936 (SnapDragon 610)
Qualcomm MSM 8937 (SnapDragon 430)
Qualcomm MSM 8939 (SnapDragon 615)
Qualcomm MSM 8974/A/AA/AB (SnapDragon 801)
Qualcomm MSM 8952 (SnapDragon 617)
Qualcomm MSM 8953 (SnapDragon 625)
Qualcomm MSM 8956 (SnapDragon 650)
Qualcomm MSM 8976 (SnapDragon 652)
Qualcomm MSM 8976 Pro (SnapDragon 653)
Qualcomm MSM 8992 (SnapDragon 808)
Qualcomm MSM 8994 (SnapDragon 810)
Qualcomm MSM 8996 (SnapDragon 820)
Qualcomm MSM 8996 Pro (SnapDragon 821)

- Main
FH Protocol updated and revised
Connection stack revised
Flashing speed increased
Support for new memory type ( UFS )
Support Multi-Drive bundles flashing ( Factory/Infinity FW )
Automatic faster loader selection if FW contain few loader types

- More Secure and Generic types supported
MSM8909: Updated support for wide range of new devices - Alcatel, ZTE, Oppo etc.
MSM8916: Updated support for wide range of new devices - Alcatel, CoolPad etc.
MSM8936: Updated support for wide range of new devices - Asus, ZTE, and etc.
MSM8974: Updated support for wide range of new devices - ZTE, Generic etc.
MSM8974: AA and AC revisions of MSM8974 support fixed
MSM8976: Updated support for wide range of new devices
MSM8992: Updated support for wide range of new devices
MSM8x2x: updated list of supported sub-types and more models supported
All types : ZTE Nubia series support ( 8936,8937,8952,8976,8996 )
Some others types supported ( total ~130 secure types and 32 generic )

P.S. : As ordinary, you do not need to spend time on "handjobs" for correct loader or models selection by bruteforce

- Flasher engine updated
Support automatic detection of multi-xml bundles for UFS and eMMC devices
Patch operations fixed on some old devices
"Force Wipe" option enabled during flashing
MSM8996/MSM8996 Pro supported

- MSM8996 supported
Identify
Factory (RAW) firmware flashing
Infinity firmware flashing
Firmware reading
Memory Tool
Reset FileSystem
Reset FRP
Reset UserLocks ( in case of not encrypted FS )
UserData Recovery ( in case of not encrypted FS )
MemoryTool
Automatic eMMC/UFS detection

- MSM8996 Pro supported
Identify
Factory (RAW) firmware flashing
Infinity firmware flashing
Firmware reading
Memory Tool
Reset FileSystem
Reset FRP
Reset UserLocks ( in case of not encrypted FS )
UserData Recovery ( in case of not encrypted FS )
MemoryTool
Automatic eMMC/UFS detection

- MSM8976 Pro supported
Identify
Factory (RAW) firmware flashing
Infinity firmware flashing
Firmware reading
Memory Tool
Reset FileSystem
Reset FRP
Reset UserLocks ( in case of not encrypted FS )
UserData Recovery ( in case of not encrypted FS )
MemoryTool

- MemoryTool
Ultimate tool for custom flashing, modding, forensic and others operations now cover UFS!
- Activated UFS memory support
Read memory
Write memory
Erase memory
Test memory
Access to any memory regions on all available LUNs
Automatic active LUN's count detection
- Improved eMMC memory support
Access to any memory regions on all available partitions
Automatic active parts count detection

Enabled "Switch Disk" option, allow switch between LUNs on UFS devices
Enabled "Switch Disk" option, allow switch between eMMC regions on eMMC devices
Enabled "Select All parts" and "Unselect all parts" options
Range now shown in partition info ( start;end;len )
Range checking activated during writing
Optimized sparse files flashing

Firmware Reader engine updated
Read all available drives for UFS devices
Read all available drives for eMMC devices
New types supported ( brand-specific - LG, Oppo, Hisense, Infocus and generic types )

-> Unlike other "solutions", CM2 make FIRMWARE, NOT A STUPID PLAIN DUMP ( i.e. cloning )
-> That means all device unique data, security etc. will remain safe after flashing!

- Other
UFS memory type extended logging support
Automatic eMMC/UFS detection for latest devices
Xiaomi account reset revised
Reset FRP procedure revised, new types supported
Some other improvements and fixes

- Additional
Unlike existing qlm "solutions" :
CM2 exactly know which device it can boot and which not.
CM2 works without the use of crutches in the form of manual selection or blunt search by bruteforce.
CM2 support widest range of secure devices ( and almost all existing unsecured )
CM2 not have any super "autodetection" mode, it just select correct loader for need device

Infinity Chinese Miracle-2 QLM v1.13 - More secure models and features

Supported CPU List:
Qualcomm MSM 8210 (SnapDragon 200)
Qualcomm MSM 8212 (SnapDragon 200)
Qualcomm MSM 8610 (SnapDragon 200)
Qualcomm MSM 8612 (SnapDragon 200)
Qualcomm MSM 8226 (SnapDragon 400)
Qualcomm MSM 8626 (SnapDragon 400)
Qualcomm MSM 8926 (SnapDragon 400)
Qualcomm MSM 8228 (SnapDragon 400)
Qualcomm MSM 8628 (SnapDragon 400)
Qualcomm MSM 8928 (SnapDragon 400)
Qualcomm APQ 8009 (SnapDragon 210)
Qualcomm MSM 8209 (SnapDragon 210)
Qualcomm MSM 8909 (SnapDragon 210)
Qualcomm MSM 8916 (SnapDragon 410)
Qualcomm MSM 8917 (SnapDragon 425)
Qualcomm MSM 8929 (SnapDragon 415)
Qualcomm MSM 8936 (SnapDragon 610)
Qualcomm MSM 8937 (SnapDragon 430)
Qualcomm MSM 8939 (SnapDragon 615)
Qualcomm MSM 8940 (SnapDragon 435)
Qualcomm MSM 8974/A/AA/AB (SnapDragon 801)
Qualcomm MSM 8952 (SnapDragon 617)
Qualcomm MSM 8953 (SnapDragon 625)
Qualcomm MSM 8956 (SnapDragon 650)
Qualcomm MSM 8976 (SnapDragon 652)
Qualcomm MSM 8976 Pro (SnapDragon 653)
Qualcomm MSM 8992 (SnapDragon 808)
Qualcomm MSM 8994 (SnapDragon 810)
Qualcomm MSM 8996 (SnapDragon 820)
Qualcomm MSM 8996 Pro (SnapDragon 821)

- Main
FH Protocol updated and revised

- More Secure and Generic types supported
MSM8909,MSM8916,MSM8936,MSM8939,MSM8940,MSM8976 : YunOS/AliGroup, BBK, VIVO, and Generic Secure Chinese types
Some others types supported ( total ~135 secure types and 33 generic )

- MemoryTool
Ultimate tool for custom flashing, modding, forensic and others operations!
New features:
> Init PMT can be done now by user on ANY need drive ( previous mode can be done only on default )
> Set BootPartition on need drive

- Security operations in EDL mode activated
Backup Security
Restore Security
Wipe Security

Firmware Reader engine updated
New types supported ( brand-specific and generic types )

-> Unlike other "solutions", CM2 make FIRMWARE, NOT A STUPID PLAIN DUMP ( i.e. cloning )
-> That means all device unique data, security etc. will remain safe after flashing!

- Other
Fixed eMMC/UFS detection for SD820/8996
Some other improvements and fixes

Infinity Chinese Miracle-2 QLM v1.14 - SnapDragon 835 / MSM8998 and other stuff

Supported CPU List:
Qualcomm MSM 8210 (SnapDragon 200)
Qualcomm MSM 8212 (SnapDragon 200)
Qualcomm MSM 8610 (SnapDragon 200)
Qualcomm MSM 8612 (SnapDragon 200)
Qualcomm MSM 8226 (SnapDragon 400)
Qualcomm MSM 8626 (SnapDragon 400)
Qualcomm MSM 8926 (SnapDragon 400)
Qualcomm MSM 8228 (SnapDragon 400)
Qualcomm MSM 8628 (SnapDragon 400)
Qualcomm MSM 8928 (SnapDragon 400)
Qualcomm APQ 8009 (SnapDragon 210)
Qualcomm MSM 8209 (SnapDragon 210)
Qualcomm MSM 8909 (SnapDragon 210)
Qualcomm MSM 8916 (SnapDragon 410)
Qualcomm MSM 8917 (SnapDragon 425)
Qualcomm MSM 8929 (SnapDragon 415)
Qualcomm MSM 8936 (SnapDragon 610)
Qualcomm MSM 8937 (SnapDragon 430)
Qualcomm MSM 8939 (SnapDragon 615)
Qualcomm MSM 8940 (SnapDragon 435)
Qualcomm MSM 8974/A/AA/AB (SnapDragon 801)
Qualcomm MSM 8952 (SnapDragon 617)
Qualcomm MSM 8953 (SnapDragon 625)
Qualcomm MSM 8956 (SnapDragon 650)
Qualcomm MSM 8976 (SnapDragon 652)
Qualcomm MSM 8976 Pro (SnapDragon 653)
Qualcomm MSM 8992 (SnapDragon 808)
Qualcomm MSM 8994 (SnapDragon 810)
Qualcomm MSM 8996 (SnapDragon 820)
Qualcomm MSM 8996 Pro (SnapDragon 821)
Qualcomm MSM 8998 (SnapDragon 835)

- MSM8998 supported
Identify
Factory (RAW) firmware flashing
Infinity firmware flashing
Firmware reading
Memory Tool
Reset FileSystem
Reset FRP
Reset UserLocks ( in case of not encrypted FS )
UserData Recovery ( in case of not encrypted FS )
MemoryTool
Automatic eMMC/UFS detection
EDL Security operations


- Main
FH Protocol updated and revised
MSM8998 supported
MSM8996 Pro for some secure types support revised ( Xiaomi and similar )
Tested and optimized support for big flash storage ( 128+ GiB )

- Flasher
Enabled DefaultBoot selection setting ( normally it selected AUTO! Use ONLY if sure about they needs to be changed! )
Optimized FlashFiles selector, some new FW types supported
Increased flashing speed

- More Secure and Generic types supported
MSM8909, MSM8916, MSM8936, MSM8996 : Generic Secure Chinese types, Alcatel and some Oppo
MSM8998 : Generic, Xiaomi types support activated

- MemoryTool
Ultimate tool for custom flashing, modding, forensic and others operations!
BootPartition selection revised
Sparse Files flashing speed increased up to 3-5 times!
Read/write operations now faster 2-4 times
Regions detection revised

- Service operations improved
FormatFS operations revised ( Repair and ForceFix mode )
Xiaomi account reset revised ( stuck on detection parameters fixed )

- Firmware Reader engine updated
New types supported ( brand-specific and generic types )
MSM8998 supported
Oppo-specific changes and fixes ( nvm errors require reflash with "Force Flash" enabled )
Sparsing big files optimized ( lower memory usage, better size decreasing )
Default regions, device-spicific regions creations activated ( make default factory partitions/files )

-> Unlike other "solutions", CM2 make FIRMWARE, NOT A STUPID PLAIN DUMP ( i.e. cloning )
-> That means all device unique data, security etc. will remain safe after flashing!

- Other
UFS memory type extended logging support revised ( Xiaomi devices )
Complete core migration for support different FlashTypes and CPU types in automatic model ( MemoryTool and Generic )
Optimized MemoryTool core - if you know how solder FlashIC's - make in-home UFS programmer not a problem
DataDirect engine updated
Some other improvements and fixes

Infinity-Box Android Service Tool / AST v1.00 - Initial release

MOTO tab activated:
-Initial Motorola line devices support
Android 5, 6, 7 lines tested and found working

Features:
Identify ( Read info, device state, frp info and rest )
Firmware flashing ( XML.ZIP packages ) Support USERDATA SAFE and COMPLETE flashing mode
Reset Settings ( Format FS )
Reset Modem misc settings
Enable ADB ( Android 5, 6, 7 devices )
Reset FRP in ADB mode ( MOTO, Generic ) via SetupMaster bypass

Drivers are in support area

Infinity-Box Chinese Miracle-2 RKT/RockChip v2.00 - New CPUs, TVbox, Tablets and more

Support RK29xx series ( NAND )
Support RK30xx series ( NAND, eMMC )
Support RK31xx series ( NAND, eMMC )
Support RK32xx series ( NAND, eMMC )
Support RK33xx series ( NAND, eMMC )

Supported devices : Tablets, TVboxes and IoT devices!

Main:
Core completely rewrittend from scratch
New connection stuck, fixed all connection problems, support latest devices and drivers

Features :
Identify / Read Info
-> Read full device info ( HW details, Android Info )
Reset Settings
-> Reset Settings ( Data and Security settings )
-> Reset UserStorage ( Photo, video and rest content )
-> Reset FRP for Android 5 / Android 6 devices
Flash Read
-> Read Factory-like FW
-> Engine allow auto-detection of different types
Flash Write
-> Write Infinity FW
-> Reset Settings during Flashing
Reset UserLocks ( eMMc Only for now )
-> Reset all userlocks without touching userdata ( Android 4/5/6 devices )
Read PatternLock
-> Allow read PatternLock sequence on Android 4/5 devices

Other
New drivers supported (visit support area to download)
DOC included: Connection hints
DOC included: eMMC and DDR support list
Old FW types (made by RKTv1) are NOT supported !
-> Workaround: Write with v1 and then read with v2 again

Infinity Chinese Miracle-2 SPD/Spreadtrum v1.27 - SC773x Android 7 and FP Forensic

SP Platform:

Activated SC773x Android 7 support
Identify (service/boot)
Read firmware ( SC/PAC )
Write Firmware ( SC/PAC )
Reset Settings/Format FS
Reset FRP
Flash erase
NVM operations: Read, Write, Clear, Fix BB
Repair Security (Normal and Flash Mode)
SP Unlock
eMMC test
HW info read/write

- Service operations improved
FRP reset improved

- Firmware reader updated
New types supported

FP Platform:

- Main
Revised bootloader package
Booting issues on some models should be fixed

- Unique UserData fatures activted!
SC6500, SC6530, SC6531: Activated Direct PhoneBook recovery/extraction!
Automatic detection of different phonebook types
Support recovery for deleted/changed records !
It's possible to make recovery for device with ANY state as soon as it can be connected to PC ( except Format FS / Dump reflash )

SC653x Samsung: Revised PhoneBook recovery/extraction
Support recovery for deleted/changed records !

- Other
Some bugfixes and improvements at all
FlashLoader package updated

Infinity-Box Chinese Miracle-2 RKT/RockChip v2.01 - Factory IMG flashing and more

- Main
Activated Factory UIMG files support
- > Flash Factory UIMG Files
- > Read Complete Info from UIMG files
- > Verify Factory UIMG files content

Activated DEVICE MODE verification
- > There is 3 mode can be found:
1. Loader Open
2. MaskROM
3. Loader Protected
PROTECTED mode limitations: WRITE PROTECTED ( you can ONLY read fw, patternlock, identify )

- Service
Activated CPU/HW details info reading
Improved NAND support
Improved "Reset UserLocks"

- Firmware Reader updated
Some missed and new types supported

- Other
Fixed connection problems with some devices
Some improvements and bugfixes

Infinity-Box Chinese Miracle-2 MTK/MediaTek : Supplementary files package for v1.58

- Boot package updated

- Ini updated, new devices are supported:
Original Nokia 3 phone ( Unique! )
Base Secure Phones
Huawei (TITx and similar)

Select "SP : Select model" and choose need mode/model

- Support package
Lot of new DRAM and eMMC config included

How to use: just install files and you will see boot selection menu

Infinity Chinese Miracle-2 QLM v1.15 - Nokia5, Nokia6, Nokia6CN, new features

Supported CPU List:
Qualcomm MSM 8210 (SnapDragon 200)
Qualcomm MSM 8212 (SnapDragon 200)
Qualcomm MSM 8610 (SnapDragon 200)
Qualcomm MSM 8612 (SnapDragon 200)
Qualcomm MSM 8226 (SnapDragon 400)
Qualcomm MSM 8626 (SnapDragon 400)
Qualcomm MSM 8926 (SnapDragon 400)
Qualcomm MSM 8228 (SnapDragon 400)
Qualcomm MSM 8628 (SnapDragon 400)
Qualcomm MSM 8928 (SnapDragon 400)
Qualcomm APQ 8009 (SnapDragon 210)
Qualcomm MSM 8209 (SnapDragon 210)
Qualcomm MSM 8909 (SnapDragon 210)
Qualcomm MSM 8916 (SnapDragon 410)
Qualcomm MSM 8917 (SnapDragon 425)
Qualcomm MSM 8929 (SnapDragon 415)
Qualcomm MSM 8936 (SnapDragon 610)
Qualcomm MSM 8937 (SnapDragon 430)
Qualcomm MSM 8939 (SnapDragon 615)
Qualcomm MSM 8940 (SnapDragon 435)
Qualcomm MSM 8974/A/AA/AB (SnapDragon 801)
Qualcomm MSM 8952 (SnapDragon 617)
Qualcomm MSM 8953 (SnapDragon 625)
Qualcomm MSM 8956 (SnapDragon 650)
Qualcomm MSM 8976 (SnapDragon 652)
Qualcomm MSM 8976 Pro (SnapDragon 653)
Qualcomm MSM 8992 (SnapDragon 808)
Qualcomm MSM 8994 (SnapDragon 810)
Qualcomm MSM 8996 (SnapDragon 820)
Qualcomm MSM 8996 Pro (SnapDragon 821)
Qualcomm MSM 8998 (SnapDragon 835)


- Original Nokia phones line ( HMD Global ) supported - WorldFirst!
Nokia 5 ( all TA-10xx revisions )
Nokia 6 ( all TA-10xx revisions )
Nokia 6CN ( all TA-10xx revisions )

Supported operations:
Read Info ( Identify )
Format FS / Reset Settings
Reset FRP
MemoryTool
Read Firmware
Flash Firmware

Since all Nokia Devices are encrypted from factory - Reset UserLocks and Forensic useless.
Strictly recommended NOT use "Force Flashing" option with Nokia devices!
After Flashing/Reset device may stuck on boot - just use VOLup + Power Key, until device will not reboot

- Main
FH Protocol updated and revised
Core revised, no more stuck boot problems
MSM8976 Pro new revision supported

- Flasher
DefaultBoot setting removed, complete auto
SafeRegions detection improved

- More Secure and Generic types supported
MSM8909, MSM8916: Generic Secure Chinese types, Alcatel and some Oppo
MSM8976, MSM8953, MSM8956: Generic Secure Chinese types, Alcatel, Lenovo and some others
MSM8936: Cover more Cyanogen based models
MSM8976 Pro: new revisions and more models

- Service operations improved
FormatFS operations revised ( Repair and ForceFix mode )
Xiaomi account reset revised
-> Reset MI Account revised
-> MICloud Services remove enabled
Disable services must be used after complete device offline setup!

- Firmware Reader engine updated
New types supported ( brand-specific and generic types )
Files verification revised
Nokia Series support

-> Unlike other "solutions" CM2 make FIRMWARE BUT NOT A USELESS PLAIN DUMP ( i.e. cloning )
-> That means all device unique data, security etc. will remain safe after flashing!

- Other
DataDirect engine updated
Some other improvements and fixes

Infinity Samsung software v1.01

List of changes:

Flash:
- Firmware write procedure rebuilded
- New feature: automatic files sort for firmware files
- New feature: it is possible to select several files to write/flash
Service:
- New feature: FRP/ReactivationsLock reset procedure released (ADB should be enabled for this option)
- New feature: NVR reading option

To activate this software please read Instruction - https://www.infinity-box.com/doc/?r=21

Infinity-Box Android Service Tool / AST v1.01 - first update

Fastboot tab activated:
- Identify / Read device info
- Reset FRP ( MTK, SPRD, QLM mode )
- Change mode ( Normal, Bootloader, Recovery, EDL )

Motorola:
- Improved Flashing engine
In case of downgrade SW will ask about force flashing ( if bootloader unlocked )
Improved flashing : timeout fixes for big blocks
Improved flashing : revised flash pre-verification
Improved flashing : FW check and verify revised
- Enabled Bootloader operations
Get Unlock token - get data for Motorola boot unlock ( via MotoUnlockDev support )
Send unlock token - apply boot unlock code to device ( just copy received code in buffer )
- Improved ADB enable function
- Improved Reset FRP function

Other
FastBoot/ADB protocols revised
Some main core changes and bugfixes

Infinity Samsung software v1.02

Main
- Qualcomm Diag protocol support added
- Qualcomm Diag port automatic detection added
Flash
- UI option to reboot device after flash
Service
- QCN backup procedure released for Qualcomm based units with enabled Diag port.
- FRP/RL lock reset procedure imporoved
UserData
- User data backup operation released. See /doc/User_data_backup.txt file for instruction

To activate this software please read Instruction - https://www.infinity-box.com/doc/?r=21

Infinity Samsung software v1.03

Internal
- Many changes regarding automatic platform/model detection, connection method and active interfaces
- In many cases it's no need to manually select model, platfoorm, port and connection method.
Just connect unit and click to "Read Info" button and software will try to detect model, platform, Root access and
according to received information and active interfaces (diag, adb) software will enable required features.

Service
- Cert write function for Spredroom platform (J320 and similar)
- Autodetection for Duos-models for automatic read and write "Duos" certificate

System
- Improvements and fixes as per users reports regarding previous versions
- New models support methods improved - some kind of autodetection methods released to make automatic support for already known platforms and Android version