.::CM2 MT2 SUCCESS REPORTs::.

Post Reply
gracy_elec
Posts: 34
Joined: 07 Jul 2019, 04:59

.::CM2 MT2 SUCCESS REPORTs::.

Post by gracy_elec »

SUCCESSFULLY TEAR PATTERN & FRP(TECNO IN1 AND:8.1.0 MT6739)USB

Operation : Identify [ v2.06 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM (Android) (COM31)
MODE : PRELOADER PORT
PORT : 31
Waiting BOOT ack ...
PRELOADER : ACK confirmed!
BROM : Init BROM
BROM init passed!
CHIP : MT6739 , SBID : 0x8A00 , HWVR : 0xCB00 , SWVR : 0x0002
TYPE : MODERN RAPHAEL
BROM : SecLevel : 0x00000005
BROM : SecMode : SBC+SDA
BROM : PRELOADER PORT
MODE : TECNO : BASE_SECURE | Manual : Disabled
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6739

AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : PRELOADER
DA : EXT_RAM initialized!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

SRAM: 0x00040000 [ 256.00 KB ]
DRAM: 0x80000000 [ 2.00 GB ]

EMMC: 150100514536334D4203F5F4E41195A5
EMMC: VEN : SAMSUNG | OEM : 01 | DEV : QE63MB
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x00400000 [ 4.00 MB ]
USER : 0x3A3E00000 [ 14.56 GB ]

CHIP : MT6739 , SBID : 0x8A00 , HWVR : 0xCB00 , SWVR : 0x0000 , EVOL : 0x0000

RNID : FDF114B7F6D2BC225EBCBEA0A4FB1836

DA : USB : HIGH-SPEED

Boot done!

Patch Level : O11019
Display ID : IN1-H398A-O-190215V268
Ver. CodeName : REL
Ver. Release : 8.1.0
Sec. Patch : 2019-02-05
Build Time : 1550222527
Product Brand : TECNO
Product Manfct : TECNO MOBILE LIMITED
Product Model : TECNO IN1
Product Device : TECNO-IN1
Product Name : H398
Product Info : TECNO-IN1
Board Platform : mt6739

USERDATA : ENCRYPTED

NVRAM check : Passed!

Backup sensetive data [ 10 ]
Backup path : Backup\MT6739__FDF114B7F6D2BC225EBCBEA0A4FB1836\
[22] Read : NVRAM
[8] Read : NVDATA
[15] Read : PROINFO
[23] Read : LK
[7] Read : NVCFG
[10] Read : PROTECT1
[11] Read : PROTECT2
[13] Read : PERSIST
[0] Read : PRELOADER
Backup done!



Done!
Elapsed: 00:00:30

Operation : Reset Settings/Format FS [ v2.06 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM (Android) (COM31)
MODE : PRELOADER PORT
PORT : 31
Waiting BOOT ack ...
PRELOADER : ACK confirmed!
BROM : Init BROM
BROM init passed!
CHIP : MT6739 , SBID : 0x8A00 , HWVR : 0xCB00 , SWVR : 0x0002
TYPE : MODERN RAPHAEL
BROM : SecLevel : 0x00000005
BROM : SecMode : SBC+SDA
BROM : PRELOADER PORT
MODE : TECNO : BASE_SECURE | Manual : Disabled
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6739

AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : PRELOADER
DA : EXT_RAM initialized!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

SRAM: 0x00040000 [ 256.00 KB ]
DRAM: 0x80000000 [ 2.00 GB ]

EMMC: 150100514536334D4203F5F4E41195A5
EMMC: VEN : SAMSUNG | OEM : 01 | DEV : QE63MB
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x00400000 [ 4.00 MB ]
USER : 0x3A3E00000 [ 14.56 GB ]

CHIP : MT6739 , SBID : 0x8A00 , HWVR : 0xCB00 , SWVR : 0x0000 , EVOL : 0x0000

RNID : FDF114B7F6D2BC225EBCBEA0A4FB1836

DA : USB : HIGH-SPEED

Boot done!

Format Ok : USERDATA
Format Ok : CACHE
Format Ok : RESET PROTECTION
Format Ok : USERDATA


Done!
Elapsed: 00:00:29

Reconnect Power/Cable!
THANKS INFINITY-BOX TEAM
gracy_elec
Posts: 34
Joined: 07 Jul 2019, 04:59

VIVO Y81 1808 AND:8.1.0 MT6765 TEAR PATTERN & FRP Done

Post by gracy_elec »

SUCCESSFULLY TEAR PATTERN & FRP(VIVO Y81 1808 AND:8.1.0 MT6765)USB

Operation : Identify [ v2.06 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM (Android) (COM31)
MODE : PRELOADER PORT
PORT : 31
Waiting BOOT ack ...
PRELOADER : ACK confirmed!
BROM : Init BROM
BROM init passed!
CHIP : MT6765 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
TYPE : MODERN RAPHAEL
BROM : SecLevel : 0x00000005
BROM : SecMode : SBC+SDA
BROM : PRELOADER PORT
MODE : Vivo : V15 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA_VIP.bin
AGENT : Found MT6765

AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : PRELOADER
DA : EXT_RAM initialized!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

SRAM: 0x00040000 [ 256.00 KB ]
DRAM: 0x30000000 [ 768.00 MB ]

EMMC: 90014A68423861503E03667085A66597
EMMC: VEN : HYNIX | OEM : 4A01 | DEV : hB8aP>
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x01000000 [ 16.00 MB ]
USER : 0x747C00000 [ 29.12 GB ]

CHIP : MT6765 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

RNID : EABF4976C597F33E39F9E5DA039FEE1

DA : USB : HIGH-SPEED

Boot done!

Patch Level : O11019
Display ID : O11019 release-keys
Ver. CodeName : REL
Ver. Release : 8.1.0
Sec. Patch : 2018-11-05
Build Time : 1545040616
Product Model : vivo 1808
Product Brand : vivo
Product Name : PD1732F_EX
Product Device : PD1732F_EX
Product Manfct : vivo
Product Info : k62v1_64_bsp
Product Model : PD1732F_EX
Product Board : k62v1_64_bsp
Board Platform : mt6765

USERDATA : ENCRYPTED

NVRAM check : Passed!

Backup sensetive data [ 10 ]
Backup path : Backup\MT6765__EABF49760C597F33E39F9E5DA039FEE1\
[31] Read : NVRAM
[8] Read : NVDATA
[20] Read : PROINFO
[32] Read : LK
[7] Read : NVCFG
[15] Read : PROTECT1
[16] Read : PROTECT2
[18] Read : PERSIST
[0] Read : PRELOADER
Backup done!



Done!
Elapsed: 00:00:34

Operation : Reset Settings/Format FS [ v2.06 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM (Android) (COM31)
MODE : PRELOADER PORT
PORT : 31
Waiting BOOT ack ...
PRELOADER : ACK confirmed!
BROM : Init BROM
BROM init passed!
CHIP : MT6765 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
TYPE : MODERN RAPHAEL
BROM : SecLevel : 0x00000005
BROM : SecMode : SBC+SDA
BROM : PRELOADER PORT
MODE : Vivo : V15 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA_VIP.bin
AGENT : Found MT6765

AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : PRELOADER
DA : EXT_RAM initialized!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

SRAM: 0x00040000 [ 256.00 KB ]
DRAM: 0x30000000 [ 768.00 MB ]

EMMC: 90014A68423861503E03667085A66597
EMMC: VEN : HYNIX | OEM : 4A01 | DEV : hB8aP>
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x01000000 [ 16.00 MB ]
USER : 0x747C00000 [ 29.12 GB ]

CHIP : MT6765 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

RNID : EABF4976C597F33E39F9E5DA039FEE1

DA : USB : HIGH-SPEED

Boot done!

Format Ok : USERDATA
Format Ok : CACHE
Format Ok : RESET PROTECTION
Format Ok : USERDATA


Done!
Elapsed: 00:00:36

Reconnect Power/Cable!

Operation : Memory Tool Init [ v2.06 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM (Android) (COM31)
MODE : PRELOADER PORT
PORT : 31
Waiting BOOT ack ...
PRELOADER : ACK confirmed!
BROM : Init BROM
BROM init passed!
CHIP : MT6765 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
TYPE : MODERN RAPHAEL
BROM : SecLevel : 0x00000005
BROM : SecMode : SBC+SDA
BROM : PRELOADER PORT
MODE : Vivo : V15 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA_VIP.bin
AGENT : Found MT6765

AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : PRELOADER
DA : EXT_RAM initialized!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

SRAM: 0x00040000 [ 256.00 KB ]
DRAM: 0x30000000 [ 768.00 MB ]

EMMC: 90014A68423861503E03667085A66597
EMMC: VEN : HYNIX | OEM : 4A01 | DEV : hB8aP>
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x01000000 [ 16.00 MB ]
USER : 0x747C00000 [ 29.12 GB ]

CHIP : MT6765 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

RNID : EABF4976C597F33E39F9E5DA039FEE1

DA : USB : HIGH-SPEED

Boot done!

Set default path : C:\InfinityBox\CM2MT2\phdata\

Ready!

Operation : Erase Memory

Erase selected partitions [3]
[0] Erase partition : FRP
Erase partition Ok!
[1] Erase partition : CACHE
Erase partition Ok!
[2] Erase partition : USERDATA
Erase partition Ok!

Operation finished!


Close MemoryTool session


Done!
Elapsed: 00:00:40

Reconnect Power/Cable!
THANKS INFINITY-BOX TEAM
gracy_elec
Posts: 34
Joined: 07 Jul 2019, 04:59

OPPO REALME 1 CPH1861 AND:9 MT6771 TEAR PATTER & FRP Done

Post by gracy_elec »

SUCCESSFULLY TEAR PATTER & FRP(OPPO REALME 1 CPH1861 AND:9 MT6771)USB

Operation : Identify [ v2.06 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek USB Port (COM97)
MODE : BOOTROM
PORT : 97
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6771 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
TYPE : MODERN RAPHAEL
BROM : SecLevel : 0x000000E5
BROM : SecMode : SBC+SDA+ARB
BROM : BOOTROM
MODE : Oppo : F7 | Manual : Disabled
BROM : ARB : ACTIVE : LOG : F0: 102B 0000 F3: 4000 0036 [0200] F3: 4000 0036 F7: 102D 0000 00: 1005 0000 F3: 4000 0036 [0200] F3: 4000 0036 F7: 102D 0000 01: 102A 0001

BROM : SOCID : 2FBC5FE18D294065D506620EDF35C938F6C11C6E53D39B99DBB15897D1ACF48D
BROM : SLA
BROM : SLA Passed!
BROM : SLA CHLNG not used
AGENT : Look for suitable BootChain in DA ...
AGENT : DA_BR_HIGH.bin
AGENT : Found MT6771

AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : BROM
DA : EXT_RAM NOT initialized!
EMI : DEV : INFINITY
EMI : SRC : INFINITY-BOX_INTERNAL_EMIDB_v0
EMI : CNT : 000E
EMI : Init EMI from INTERNAL DB
EMI : EXT_RAM CFG Passed!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

SRAM: 0x00040000 [ 256.00 KB ]
DRAM: 0xC0000000 [ 3.00 GB ]

EMMC: 150100335636434D42028877AA8135BD
EMMC: VEN : SAMSUNG | OEM : 01 | DEV : 3V6CMB
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x01000000 [ 16.00 MB ]
USER : 0x1D1EC00000 [ 116.48 GB ]

CHIP : MT6771 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

RNID : 7F85A0F89DA64F81B12CF6E12007144

DA : USB : HIGH-SPEED

Boot done!

Patch Level : PPR1.180610.011
Ver. CodeName : REL
Ver. Release : 9
Sec. Patch : 2019-05-05
Product Manfct : OPPO
Build Time : 1561144775
Product Brand : OPPO
Product Brand : Realme
Product Model : CPH1861
Product Info : CPH1861
Product Name : CPH1861
Product Device : CPH1861
SW OTA Version : CPH1861EX_11.A.37_0370_201906220259
Display ID : CPH1861EX_11_A.37
Kernel Info : 4.4.146

USERDATA : ENCRYPTED

NVRAM check : Passed!

Backup sensetive data [ 10 ]
Backup path : Backup\MT6771__7F85A0F89DA64F81B12CF6E102007144\
[33] Read : NVRAM
[14] Read : NVDATA
[21] Read : PROINFO
[34] Read : LK
[13] Read : NVCFG
[16] Read : PROTECT1
[17] Read : PROTECT2
[19] Read : PERSIST
[0] Read : PRELOADER
Backup done!



Done!
Elapsed: 00:23:17

Operation : Reset Settings/Format FS [ v2.06 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek USB Port (COM97)
MODE : BOOTROM
PORT : 97
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6771 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
TYPE : MODERN RAPHAEL
BROM : SecLevel : 0x000000E5
BROM : SecMode : SBC+SDA+ARB
BROM : BOOTROM
MODE : Oppo : F7 | Manual : Disabled
BROM : ARB : ACTIVE : LOG : F0: 102B 0000 F3: 4000 0036 [0200] F3: 4000 0036 F7: 102D 0000 00: 1005 0000 F3: 4000 0036 [0200] F3: 4000 0036 F7: 102D 0000 01: 102A 0001

BROM : SOCID : 2FBC5FE18D294065D506620EDF35C938F6C11C6E53D39B99DBB15897D1ACF48D
BROM : SLA
BROM : SLA Passed!
BROM : SLA CHLNG not used
AGENT : Look for suitable BootChain in DA ...
AGENT : DA_BR_HIGH.bin
AGENT : Found MT6771

AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : BROM
DA : EXT_RAM NOT initialized!
EMI : DEV : INFINITY
EMI : SRC : INFINITY-BOX_INTERNAL_EMIDB_v0
EMI : CNT : 000E
EMI : Init EMI from INTERNAL DB
EMI : EXT_RAM CFG Passed!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

SRAM: 0x00040000 [ 256.00 KB ]
DRAM: 0xC0000000 [ 3.00 GB ]

EMMC: 150100335636434D42028877AA8135BD
EMMC: VEN : SAMSUNG | OEM : 01 | DEV : 3V6CMB
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x01000000 [ 16.00 MB ]
USER : 0x1D1EC00000 [ 116.48 GB ]

CHIP : MT6771 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

RNID : 7F85A0F89DA64F81B12CF6E12007144

DA : USB : HIGH-SPEED

Boot done!

Format Ok : USERDATA
Format Ok : CACHE
Format Ok : RESET PROTECTION
Format Ok : USERDATA


Done!
Elapsed: 00:00:40

Reconnect Power/Cable!
THANKS INFINITY-BOX TEAM
gracy_elec
Posts: 34
Joined: 07 Jul 2019, 04:59

LAVA Z60S AND:8.1.0 MT6739 READ NVRAM BAG BRUSH Done

Post by gracy_elec »

SUCCESSFULLY READ NVRAM BAG BRUSH DONE(LAVA Z60S AND:8.1.0 MT6739)USB

Operation : Identify [ v2.06 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek USB Port (COM21)
MODE : BOOTROM
PORT : 21
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6739 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
TYPE : MODERN RAPHAEL
BROM : SecLevel : 0x000000E1
BROM : SecMode : SBC+ARB
BROM : BOOTROM
MODE : Lava : Z60S | Manual : Disabled
BROM : ARB : ACTIVE : LOG : F0: 102B 0000 F3: 0000 0000 V0: 0000 0000 [0001]

BROM : SOCID : 08387D3D67ED1C3F4FF8E3D9B3C2431EA1EC7BDE81AF3EC8380A97453578322F
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6739

AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : BROM
DA : EXT_RAM NOT initialized!
EMI : DEV : MT6739
EMI : SRC : preloader.bin
EMI : CNT : 0005
EMI : [00] : eMCP : eMMC+LP/DDR3 , ID : 90014A484147346132 : VEN : HYNIX | DEV : HAG4a2 : RAM : [ 2.00 GB ]
EMI : [01] : eMCP : eMMC+LP/DDR3 , ID : 150100514536334D42 : VEN : SAMSUNG | DEV : QE63MB : RAM : [ 2.00 GB ]
EMI : [02] : eMCP : eMMC+LP/DDR3 , ID : 150100464E36324D42 : VEN : SAMSUNG | DEV : FN62MB : RAM : [ 1.00 GB ]
EMI : [03] : eMCP : eMMC+LP/DDR3 , ID : 90014A483847346132 : VEN : HYNIX | DEV : H8G4a2 : RAM : [ 1.00 GB ]
EMI : [04] : eMCP : eMMC+LP/DDR3 , ID : 150100464536324D42 : VEN : SAMSUNG | DEV : FE62MB : RAM : [ 1.00 GB ]
EMI : Init EMI from PRELOADER
EMI : EXT_RAM CFG Passed!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

SRAM: 0x00040000 [ 256.00 KB ]
DRAM: 0x40000000 [ 1.00 GB ]

EMMC: 150100464536324D4203C58CAAF58583
EMMC: VEN : SAMSUNG | OEM : 01 | DEV : FE62MB
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x00400000 [ 4.00 MB ]
USER : 0x3A3E00000 [ 14.56 GB ]

CHIP : MT6739 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

RNID : 473722B99AFB54AEEA209B969A3E17AB

DA : USB : HIGH-SPEED

Boot done!

Patch Level : O11019
Display ID : LAVA_Z60s_1_16_V1.0_S133_20190419_ENG_IN
Ver. CodeName : REL
Ver. Release : 8.1.0
Sec. Patch : 2019-04-05
Build Time : 1555653631
Product Model : Z60s
Product Brand : LAVA
Product Name : Z60s
Product Device : Z60s
Product Manfct : LAVA
Product Info : Z60s
Product Board : lava6739_sp65_in
Board Platform : mt6739

USERDATA : ENCRYPTED

NVRAM check : Passed!

Backup sensetive data [ 10 ]
Backup path : Backup\MT6739__473722B99AFB54AEEA209B969A3E17AB\
[21] Read : NVRAM
[8] Read : NVDATA
[14] Read : PROINFO
[22] Read : LK
[7] Read : NVCFG
[10] Read : PROTECT1
[11] Read : PROTECT2
[0] Read : PRELOADER
Backup done!



Done!
Elapsed: 00:00:16

Operation : Reset Settings/Format FS [ v2.06 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek USB Port (COM21)
MODE : BOOTROM
PORT : 21
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6739 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
TYPE : MODERN RAPHAEL
BROM : SecLevel : 0x000000E1
BROM : SecMode : SBC+ARB
BROM : BOOTROM
MODE : Lava : Z60S | Manual : Disabled
BROM : ARB : ACTIVE : LOG : F0: 102B 0000 F3: 0000 0000 V0: 0000 0000 [0001]

BROM : SOCID : 08387D3D67ED1C3F4FF8E3D9B3C2431EA1EC7BDE81AF3EC8380A97453578322F
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6739

AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : BROM
DA : EXT_RAM NOT initialized!
EMI : DEV : MT6739
EMI : SRC : preloader.bin
EMI : CNT : 0005
EMI : [00] : eMCP : eMMC+LP/DDR3 , ID : 90014A484147346132 : VEN : HYNIX | DEV : HAG4a2 : RAM : [ 2.00 GB ]
EMI : [01] : eMCP : eMMC+LP/DDR3 , ID : 150100514536334D42 : VEN : SAMSUNG | DEV : QE63MB : RAM : [ 2.00 GB ]
EMI : [02] : eMCP : eMMC+LP/DDR3 , ID : 150100464E36324D42 : VEN : SAMSUNG | DEV : FN62MB : RAM : [ 1.00 GB ]
EMI : [03] : eMCP : eMMC+LP/DDR3 , ID : 90014A483847346132 : VEN : HYNIX | DEV : H8G4a2 : RAM : [ 1.00 GB ]
EMI : [04] : eMCP : eMMC+LP/DDR3 , ID : 150100464536324D42 : VEN : SAMSUNG | DEV : FE62MB : RAM : [ 1.00 GB ]
EMI : Init EMI from PRELOADER
EMI : EXT_RAM CFG Passed!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

SRAM: 0x00040000 [ 256.00 KB ]
DRAM: 0x40000000 [ 1.00 GB ]

EMMC: 150100464536324D4203C58CAAF58583
EMMC: VEN : SAMSUNG | OEM : 01 | DEV : FE62MB
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x00400000 [ 4.00 MB ]
USER : 0x3A3E00000 [ 14.56 GB ]

CHIP : MT6739 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

RNID : 473722B99AFB54AEEA209B969A3E17AB

DA : USB : HIGH-SPEED

Boot done!

Format Ok : RESET PROTECTION

Done!
Elapsed: 00:00:14

Reconnect Power/Cable!
THANKS INFINITY-BOX TEAM
gracy_elec
Posts: 34
Joined: 07 Jul 2019, 04:59

GIONEE F103 PRO AND:6.0 MT6735 READ NVRAM BAB & BRUSH Done

Post by gracy_elec »

SUCCESSFULLY READ NVRAM BAG & BRUSH DONE(GIONEE F103 PRO AND:6.0 MT6735)USB

Operation : Identify [ v2.06 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM (Android) (COM34)
MODE : PRELOADER PORT
PORT : 34
Waiting BOOT ack ...
PRELOADER : ACK confirmed!
BROM : Init BROM
BROM init passed!
CHIP : MT6735 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
TYPE : LEGACY MTK
BROM : SecLevel : 0x00000000
BROM : SecMode : PLAIN [+PRL]
BROM : PRELOADER PORT
MODE : Gionee : GN3001 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ...
AGENT : DA_PL_CRYPTO.bin
AGENT : Found MT6735

AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
NAND : DEVICE NOT FOUND
NAND : 000000000000000000000000
eMMC : OK
eMMC : 150100523331424D4201AEECDA7D9F1D
DAInf: 4 : 2 : 147
DA : DRAM ready!
DA : BOOT to 2nd DA ...
DA : Receiving HW info

EMMC: 150100523331424D4201AEECDA7D831D
EMMC: VEN : SAMSUNG | OEM : 01 | DEV : R31BMB
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x00400000 [ 4.00 MB ]
USER : 0x3A3E00000 [ 14.56 GB ]

SRAM: 0x00020000 [ 128.00 KB ]
DRAM: 0xC0000000 [ 3.00 GB ]

CHIP : MT6735 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

RNID : 32B37886819AA353B03216ABACFBED64

STATUS : BLANK FLASH
BSTYLE : EMMC FLASH BOOT

DA : USB : HIGH-SPEED

Boot done!

Board Platform : mt6735
Build Time : 1495545592
Display ID : amigo3.2.0
Patch Level : MRA58K
Product Info : gionee6735_66c_m0
Ver. CodeName : REL
Ver. Release : 6.0
Sec. Patch : 2017-04-05
Product Board : F103_Pro
Product Brand : GIONEE
Product Device : GIONEE_GBL7360
Product Manfct : GIONEE
Product Model : F103 Pro
Product Name : F103_Pro

USERDATA : ENCRYPTED

IMEI[0] : 862XXXXXXXX654
IMEI[1] : 862XXXXXXXX653
NVRAM check : Passed!

Backup sensetive data [ 10 ]
Backup path : Backup\MT6735__32B37886819AA353B03216ABACFBED64\
[3] Read : NVRAM
[19] Read : NVDATA
[2] Read : PROINFO
[6] Read : LK
[4] Read : PROTECT1
[5] Read : PROTECT2
[0] Read : PRELOADER
Backup done!



Done!
Elapsed: 00:00:26

Operation : Read Security [ v2.06 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM (Android) (COM34)
MODE : PRELOADER PORT
PORT : 34
Waiting BOOT ack ...
PRELOADER : ACK confirmed!
BROM : Init BROM
BROM init passed!
CHIP : MT6735 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
TYPE : LEGACY MTK
BROM : SecLevel : 0x00000000
BROM : SecMode : PLAIN [+PRL]
BROM : PRELOADER PORT
MODE : Gionee : GN3001 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ...
AGENT : DA_PL_CRYPTO.bin
AGENT : Found MT6735

AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
NAND : DEVICE NOT FOUND
NAND : 000000000000000000000000
eMMC : OK
eMMC : 150100523331424D4201AEECDA7D9F1D
DAInf: 4 : 2 : 147
DA : DRAM ready!
DA : BOOT to 2nd DA ...
DA : Receiving HW info

EMMC: 150100523331424D4201AEECDA7D831D
EMMC: VEN : SAMSUNG | OEM : 01 | DEV : R31BMB
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x00400000 [ 4.00 MB ]
USER : 0x3A3E00000 [ 14.56 GB ]

SRAM: 0x00020000 [ 128.00 KB ]
DRAM: 0xC0000000 [ 3.00 GB ]

CHIP : MT6735 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

RNID : 32B37886819AA353B03216ABACFBED64

STATUS : BLANK FLASH
BSTYLE : EMMC FLASH BOOT

DA : USB : HIGH-SPEED

Boot done!

SEC Data :
IMEI[0] : 862XXXXXXXX654
IMEI[1] : 862XXXXXXXX653

NVRAM check : Passed!


NVM saved as : MT6735__eMMC__862XXXXXXX654.mt_sec
NVM saved to : C:\InfinityBox\CM2MT2\Backup\


Done!
Elapsed: 00:00:27

Reconnect Power/Cable!

Operation : Reset Settings/Format FS [ v2.06 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM (Android) (COM34)
MODE : PRELOADER PORT
PORT : 34
Waiting BOOT ack ...
PRELOADER : ACK confirmed!
BROM : Init BROM
BROM init passed!
CHIP : MT6735 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
TYPE : LEGACY MTK
BROM : SecLevel : 0x00000000
BROM : SecMode : PLAIN [+PRL]
BROM : PRELOADER PORT
MODE : Gionee : GN3001 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ...
AGENT : DA_PL_CRYPTO.bin
AGENT : Found MT6735

AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
NAND : DEVICE NOT FOUND
NAND : 000000000000000000000000
eMMC : OK
eMMC : 150100523331424D4201AEECDA7D9F1D
DAInf: 4 : 2 : 147
DA : DRAM ready!
DA : BOOT to 2nd DA ...
DA : Receiving HW info

EMMC: 150100523331424D4201AEECDA7D831D
EMMC: VEN : SAMSUNG | OEM : 01 | DEV : R31BMB
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x00400000 [ 4.00 MB ]
USER : 0x3A3E00000 [ 14.56 GB ]

SRAM: 0x00020000 [ 128.00 KB ]
DRAM: 0xC0000000 [ 3.00 GB ]

CHIP : MT6735 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

RNID : 32B37886819AA353B03216ABACFBED64

STATUS : BLANK FLASH
BSTYLE : EMMC FLASH BOOT

DA : USB : HIGH-SPEED

Boot done!

Format Ok : RESET PROTECTION

Done!
Elapsed: 00:00:26

Reconnect Power/Cable!
THANKS INFINITY-BOX TEAM
gracy_elec
Posts: 34
Joined: 07 Jul 2019, 04:59

VIVO Y83 1802 AND:8.1.0 MT6765 READ NVRAM BAG & BRUSH Done

Post by gracy_elec »

SUCCESSFULLY READ NVRAM BAG & BRUSH DONE(VIVO Y83 1802 AND:8.1.0 MT6765)USB

Operation : Identify [ v2.06 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek USB Port (COM32)
MODE : BOOTROM
PORT : 32
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6765 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
TYPE : MODERN RAPHAEL
BROM : SecLevel : 0x000000E5
BROM : SecMode : SBC+SDA+ARB
BROM : BOOTROM
MODE : Vivo : Y83 | Manual : Disabled
BROM : ARB : ACTIVE : LOG : F0: 102B 0000 F3: 0000 0000 [0200] V0: 0000 0000 [0001]
BROM : SOCID : A2ABE814C30B4333C95C5D2241B1B216E8BDAB3E1DEE1D82A57B70540BA01D10
BROM : SLA
BROM : SLA Passed!
BROM : SLA CHLNG not used
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA_VIP.bin
AGENT : Found MT6765

AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : BROM
DA : EXT_RAM NOT initialized!
EMI : DEV : MT6765
EMI : SRC : preloader_k62v1_64_bsp.bin
EMI : CNT : 000A
EMI : [00] : eMCP : eMMC+LP/DDR3 , ID : 150100524436344D42 : VEN : SAMSUNG | DEV : RD64MB : RAM : [ 4.00 GB ]
EMI : [01] : eMCP : eMMC+LP/DDR3 , ID : 150100524836344142 : VEN : SAMSUNG | DEV : RH64AB : RAM : [ 4.00 GB ]
EMI : [02] : eMCP : eMMC+LP/DDR3 , ID : 150100474436424D42 : VEN : SAMSUNG | DEV : GD6BMB : RAM : [ 3.00 GB ]
EMI : [03] : eMCP : eMMC+LP/DDR3 , ID : 90014A484247346132 : VEN : HYNIX | DEV : HBG4a2 : RAM : [ 4.00 GB ]
EMI : [04] : eMCP : eMMC+LP/DDR4 , ID : 150100444836444D42 : VEN : SAMSUNG | DEV : DH6DMB : RAM : [ 4.00 GB ]
EMI : [05] : eMCP : eMMC+LP/DDR4 , ID : 150100445636444D42 : VEN : SAMSUNG | DEV : DV6DMB : RAM : [ 4.00 GB ]
EMI : [06] : eMCP : eMMC+LP/DDR3 , ID : 90014A68423861503E : VEN : HYNIX | DEV : hB8aP> : RAM : [ 3.00 GB ]
EMI : [07] : eMCP : eMMC+LP/DDR3 , ID : 90014A484347386134 : VEN : HYNIX | DEV : HCG8a4 : RAM : [ 4.00 GB ]
EMI : [08] : eMCP : eMMC+LP/DDR3 , ID : 150100475036424D42 : VEN : SAMSUNG | DEV : GP6BMB : RAM : [ 3.00 GB ]
EMI : [09] : eMCP : eMMC+LP/DDR3 , ID : 150100474536424D42 : VEN : SAMSUNG | DEV : GE6BMB : RAM : [ 3.00 GB ]
EMI : Init EMI from PRELOADER
EMI : EXT_RAM CFG Passed!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

SRAM: 0x00040000 [ 256.00 KB ]
DRAM: 0x30000000 [ 768.00 MB ]

EMMC: 90014A484247346132A54BB562322537
EMMC: VEN : HYNIX | OEM : 4A01 | DEV : HBG4a2
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x00400000 [ 4.00 MB ]
USER : 0x747C00000 [ 29.12 GB ]

CHIP : MT6765 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

RNID : D85F8D8EF225CA8136E04E943A08FBDB

DA : USB : HIGH-SPEED

Boot done!

Patch Level : O11019
Display ID : O11019 release-keys
Ver. CodeName : REL
Ver. Release : 8.1.0
Sec. Patch : 2019-06-05
Build Time : 1562073099
Product Model : vivo 1802
Product Brand : vivo
Product Name : PD1803BF_EX
Product Device : PD1803BF_EX
Product Manfct : vivo
Product Info : k62v1_64_bsp
Product Model : PD1803BF_EX
Product Board : k62v1_64_bsp
Board Platform : mt6765

USERDATA : ENCRYPTED

NVRAM check : Passed!

Backup sensetive data [ 10 ]
Backup path : Backup\MT6765__D85F8D8EF225CA8136E04E943A08FBDB\
[31] Read : NVRAM
[8] Read : NVDATA
[20] Read : PROINFO
[32] Read : LK
[7] Read : NVCFG
[15] Read : PROTECT1
[16] Read : PROTECT2
[18] Read : PERSIST
[0] Read : PRELOADER
Backup done!



Done!
Elapsed: 00:00:49

Operation : Reset Settings/Format FS [ v2.06 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek USB Port (COM32)
MODE : BOOTROM
PORT : 32
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6765 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
TYPE : MODERN RAPHAEL
BROM : SecLevel : 0x000000E5
BROM : SecMode : SBC+SDA+ARB
BROM : BOOTROM
MODE : Vivo : Y83 | Manual : Disabled
BROM : ARB : ACTIVE : LOG : F0: 102B 0000 F3: 0000 0000 [0200] V0: 0000 0000 [0001]
BROM : SOCID : A2ABE814C30B4333C95C5D2241B1B216E8BDAB3E1DEE1D82A57B70540BA01D10
BROM : SLA
BROM : SLA Passed!
BROM : SLA CHLNG not used
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA_VIP.bin
AGENT : Found MT6765

AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : BROM
DA : EXT_RAM NOT initialized!
EMI : DEV : MT6765
EMI : SRC : preloader_k62v1_64_bsp.bin
EMI : CNT : 000A
EMI : [00] : eMCP : eMMC+LP/DDR3 , ID : 150100524436344D42 : VEN : SAMSUNG | DEV : RD64MB : RAM : [ 4.00 GB ]
EMI : [01] : eMCP : eMMC+LP/DDR3 , ID : 150100524836344142 : VEN : SAMSUNG | DEV : RH64AB : RAM : [ 4.00 GB ]
EMI : [02] : eMCP : eMMC+LP/DDR3 , ID : 150100474436424D42 : VEN : SAMSUNG | DEV : GD6BMB : RAM : [ 3.00 GB ]
EMI : [03] : eMCP : eMMC+LP/DDR3 , ID : 90014A484247346132 : VEN : HYNIX | DEV : HBG4a2 : RAM : [ 4.00 GB ]
EMI : [04] : eMCP : eMMC+LP/DDR4 , ID : 150100444836444D42 : VEN : SAMSUNG | DEV : DH6DMB : RAM : [ 4.00 GB ]
EMI : [05] : eMCP : eMMC+LP/DDR4 , ID : 150100445636444D42 : VEN : SAMSUNG | DEV : DV6DMB : RAM : [ 4.00 GB ]
EMI : [06] : eMCP : eMMC+LP/DDR3 , ID : 90014A68423861503E : VEN : HYNIX | DEV : hB8aP> : RAM : [ 3.00 GB ]
EMI : [07] : eMCP : eMMC+LP/DDR3 , ID : 90014A484347386134 : VEN : HYNIX | DEV : HCG8a4 : RAM : [ 4.00 GB ]
EMI : [08] : eMCP : eMMC+LP/DDR3 , ID : 150100475036424D42 : VEN : SAMSUNG | DEV : GP6BMB : RAM : [ 3.00 GB ]
EMI : [09] : eMCP : eMMC+LP/DDR3 , ID : 150100474536424D42 : VEN : SAMSUNG | DEV : GE6BMB : RAM : [ 3.00 GB ]
EMI : Init EMI from PRELOADER
EMI : EXT_RAM CFG Passed!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

SRAM: 0x00040000 [ 256.00 KB ]
DRAM: 0x30000000 [ 768.00 MB ]

EMMC: 90014A484247346132A54BB562322537
EMMC: VEN : HYNIX | OEM : 4A01 | DEV : HBG4a2
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x00400000 [ 4.00 MB ]
USER : 0x747C00000 [ 29.12 GB ]

CHIP : MT6765 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

RNID : D85F8D8EF225CA8136E04E943A08FBDB

DA : USB : HIGH-SPEED

Boot done!

Format Ok : USERDATA
Format Ok : CACHE
Format Ok : RESET PROTECTION
Format Ok : USERDATA


Done!
Elapsed: 00:00:44

Reconnect Power/Cable!

Operation : Memory Tool Init [ v2.06 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM (Android) (COM93)
MODE : PRELOADER PORT
PORT : 93
Waiting BOOT ack ...
PRELOADER : ACK confirmed!
BROM : Init BROM
BROM init passed!
CHIP : MT6765 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
TYPE : MODERN RAPHAEL
BROM : SecLevel : 0x00000005
BROM : SecMode : SBC+SDA
BROM : PRELOADER PORT
MODE : Vivo : Y83 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA_VIP.bin
AGENT : Found MT6765

AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : PRELOADER
DA : EXT_RAM initialized!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

SRAM: 0x00040000 [ 256.00 KB ]
DRAM: 0x30000000 [ 768.00 MB ]

EMMC: 90014A484247346132A54BB562322537
EMMC: VEN : HYNIX | OEM : 4A01 | DEV : HBG4a2
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x00400000 [ 4.00 MB ]
USER : 0x747C00000 [ 29.12 GB ]

CHIP : MT6765 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

RNID : D85F8D8EF225CA8136E04E943A08FBDB

DA : USB : HIGH-SPEED

Boot done!

Set default path : C:\InfinityBox\CM2MT2\phdata\

Ready!

Operation : Erase Memory

Erase selected partitions [3]
[0] Erase partition : FRP
Erase partition Ok!
[1] Erase partition : CACHE
Erase partition Ok!
[2] Erase partition : USERDATA
Erase partition Ok!

Operation finished!


Close MemoryTool session


Done!
Elapsed: 00:00:35

Reconnect Power/Cable!
THANKS INFINITY-BOX TEAM
gracy_elec
Posts: 34
Joined: 07 Jul 2019, 04:59

MICROMAX Q437 AND:8.1.0 MT6737M READ NVRAM BAG & TEAR FRP Done

Post by gracy_elec »

SUCCESSFULLY READ NVRAM BAG & TEAR FRP(MICROMAX Q437 AND:8.1.0 MT6737M)USB

Operation : Identify [ v2.06 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM (Android) (COM34)
MODE : PRELOADER PORT
PORT : 34
Waiting BOOT ack ...
PRELOADER : ACK confirmed!
BROM : Init BROM
BROM init passed!
CHIP : MT6735 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
TYPE : LEGACY MTK
BROM : SecLevel : 0x00000000
BROM : SecMode : PLAIN [+PRL]
BROM : PRELOADER PORT
MODE : 0_base : BASE_v1916 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6735

AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
NAND : DEVICE NOT FOUND
NAND : 000000000000000000000000
eMMC : OK
eMMC : 150100464E36324D4203A84FE4892281
DAInf: 4 : 2 : 155
DA : DRAM ready!
DA : BOOT to 2nd DA ...
DA : Receiving HW info

EMMC: 150100464E36324D4203A84FE4897481
EMMC: VEN : SAMSUNG | OEM : 01 | DEV : FN62MB
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x00080000 [ 512.00 KB ]
USER : 0x1D2000000 [ 7.28 GB ]

SRAM: 0x00020000 [ 128.00 KB ]
DRAM: 0x40000000 [ 1.00 GB ]

CHIP : MT6735 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

RNID : D73688356DE4D7CA29D3FF32867AE6BF

STATUS : BLANK FLASH
BSTYLE : EMMC FLASH BOOT

DA : USB : HIGH-SPEED

Boot done!

Patch Level : O11019
Display ID : MMX_Q437_SW_V14_HW_V1.0_20180404
Ver. CodeName : REL
Ver. Release : 8.1.0
Sec. Patch : 2018-02-05
Build Time : 1522834779
Product Model : Micromax Q437
Product Brand : Micromax
Product Name : Bharat_Go
Product Device : Q437
Product Manfct : Micromax
Product Info : Q437
Product Board : Q437
Board Platform : mt6737m

USERDATA : ENCRYPTED

IMEI[0] : 911XXXXXXXX097
IMEI[1] : 911XXXXXXXX591
NVRAM check : Passed!

Backup sensetive data [ 10 ]
Backup path : Backup\MT6735__D73688356DE4D7CA29D3FF32867AE6BF\
[3] Read : NVRAM
[20] Read : NVDATA
[2] Read : PROINFO
[6] Read : LK
[4] Read : PROTECT1
[5] Read : PROTECT2
[18] Read : PERSIST
[0] Read : PRELOADER
Backup done!



Done!
Elapsed: 00:00:24

Operation : Read Security [ v2.06 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM (Android) (COM34)
MODE : PRELOADER PORT
PORT : 34
Waiting BOOT ack ...
PRELOADER : ACK confirmed!
BROM : Init BROM
BROM init passed!
CHIP : MT6735 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
TYPE : LEGACY MTK
BROM : SecLevel : 0x00000000
BROM : SecMode : PLAIN [+PRL]
BROM : PRELOADER PORT
MODE : 0_base : BASE_v1916 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6735

AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
NAND : DEVICE NOT FOUND
NAND : 000000000000000000000000
eMMC : OK
eMMC : 150100464E36324D4203A84FE4892281
DAInf: 4 : 2 : 155
DA : DRAM ready!
DA : BOOT to 2nd DA ...
DA : Receiving HW info

EMMC: 150100464E36324D4203A84FE4897481
EMMC: VEN : SAMSUNG | OEM : 01 | DEV : FN62MB
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x00080000 [ 512.00 KB ]
USER : 0x1D2000000 [ 7.28 GB ]

SRAM: 0x00020000 [ 128.00 KB ]
DRAM: 0x40000000 [ 1.00 GB ]

CHIP : MT6735 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

RNID : D73688356DE4D7CA29D3FF32867AE6BF

STATUS : BLANK FLASH
BSTYLE : EMMC FLASH BOOT

DA : USB : HIGH-SPEED

Boot done!

SEC Data :
IMEI[0] : 911XXXXXXXX097
IMEI[1] : 911XXXXXXXX591

NVRAM check : Passed!


NVM saved as : MT6735__eMMC__911XXXXXXX097.mt_sec
NVM saved to : C:\InfinityBox\CM2MT2\Backup\


Done!
Elapsed: 00:00:19

Reconnect Power/Cable!

Operation : Reset Settings/Format FS [ v2.06 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM (Android) (COM34)
MODE : PRELOADER PORT
PORT : 34
Waiting BOOT ack ...
PRELOADER : ACK confirmed!
BROM : Init BROM
BROM init passed!
CHIP : MT6735 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
TYPE : LEGACY MTK
BROM : SecLevel : 0x00000000
BROM : SecMode : PLAIN [+PRL]
BROM : PRELOADER PORT
MODE : 0_base : BASE_v1916 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6735

AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
NAND : DEVICE NOT FOUND
NAND : 000000000000000000000000
eMMC : OK
eMMC : 150100464E36324D4203A84FE4892281
DAInf: 4 : 2 : 155
DA : DRAM ready!
DA : BOOT to 2nd DA ...
DA : Receiving HW info

EMMC: 150100464E36324D4203A84FE4897481
EMMC: VEN : SAMSUNG | OEM : 01 | DEV : FN62MB
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x00080000 [ 512.00 KB ]
USER : 0x1D2000000 [ 7.28 GB ]

SRAM: 0x00020000 [ 128.00 KB ]
DRAM: 0x40000000 [ 1.00 GB ]

CHIP : MT6735 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

RNID : D73688356DE4D7CA29D3FF32867AE6BF

STATUS : BLANK FLASH
BSTYLE : EMMC FLASH BOOT

DA : USB : HIGH-SPEED

Boot done!

Format Ok : RESET PROTECTION

Done!
Elapsed: 00:00:12

Reconnect Power/Cable!
THANKS INFINITY-BOX TEAM
gracy_elec
Posts: 34
Joined: 07 Jul 2019, 04:59

HTC D628H AND:5.1 MT6753 READ NVRAM BAG & BRUSH FRP Done

Post by gracy_elec »

SUCCESSFULLY READ NVRAM BAG & BRUSH FRP DONE(HTC D628H AND:5.1 MT6753)USB

Operation : Identify [ v2.06 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek USB Port (COM40)
MODE : BOOTROM
PORT : 40
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6753 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
TYPE : LEGACY MTK
BROM : SecLevel : 0x00000000
BROM : SecMode : PLAIN [+PRL]
BROM : BOOTROM
MODE : 0_base : BASE_v1724 | Manual : Disabled
Fail to disable Dog!
AGENT : Look for suitable BootChain in DA ...
AGENT : DA_SWSEC.bin
AGENT : Found MT6753

AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
NAND : DEVICE NOT FOUND
NAND : 000000000000000000000000
eMMC : OK
eMMC : 90014A484247346132A4235205284AFB
DAInf: 4 : 2 : 155
DA : EXT_RAM NOT initialized!
eMMC : OK
eMMC : 484A0190613447425223A432FB4A2805
NAND : DEVICE NOT FOUND
NAND : 000000000000000000000000
EMI : DEV : INFINITY
EMI : SRC : INFINITY-BOX_INTERNAL_EMIDB_v0
INIT : 0xBC : LP/DDR3 [ 0x00000000 : [ 0 B ] ]
DRAM : DRAM: 0xC0000000 [ 3.00 GB ]
DA : DRAM ready!
DA : BOOT to 2nd DA ...
DA : Receiving HW info

EMMC: 90014A484247346132A4235252883FB
EMMC: VEN : HYNIX | OEM : 4A01 | DEV : HBG4a2
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x00400000 [ 4.00 MB ]
USER : 0x747C00000 [ 29.12 GB ]

SRAM: 0x00020000 [ 128.00 KB ]
DRAM: 0xC0000000 [ 3.00 GB ]

CHIP : MT6753 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

RNID : B0BBE292E34250FA7420829E274D7F8

STATUS : BLANK FLASH
BSTYLE : EMMC FLASH BOOT

DA : USB : FULL-SPEED
DA : USB : Change Port Speed
PTFN : MediaTek DA USB VCOM (Android) (COM91)
MODE : PRELOADER PORT
PORT : 91

Boot done!

Product Model : HTC Desire 628 dual sim
Patch Level : LMY47D
Display ID : LMY47D release-keys
Ver. CodeName : REL
Ver. Release : 5.1
Sec. Patch : 2016-05-01
Build Time : 1470366422
Product Model : htc_v36bml_dugl
Product Brand : htc
Product Name : v36bml_dugl_00400
Product Device : htc_v36bml_dugl
Product Manfct : HTC
Board Platform : mt6753
Product Info : htc_v36bml_dugl

USERDATA : PLAIN ( NOT encrypted )

IMEI[0] : 357XXXXXXXX922
IMEI[1] : 357XXXXXXXX648
NVRAM check : Passed!

Backup sensetive data [ 10 ]
Backup path : Backup\MT6753__B0BBE2920E34250FA7420829E274D7F8\
[3] Read : NVRAM
[41] Read : NVDATA
[2] Read : PROINFO
[13] Read : LK
[4] Read : PROTECT1
[5] Read : PROTECT2
[6] Read : PERSIST
[0] Read : PRELOADER
Backup done!



Done!
Elapsed: 00:00:49

Operation : Reset Settings/Format FS [ v2.06 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek USB Port (COM40)
MODE : BOOTROM
PORT : 40
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6753 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
TYPE : LEGACY MTK
BROM : SecLevel : 0x00000000
BROM : SecMode : PLAIN [+PRL]
BROM : BOOTROM
MODE : 0_base : BASE_v1724 | Manual : Disabled
Fail to disable Dog!
AGENT : Look for suitable BootChain in DA ...
AGENT : DA_SWSEC.bin
AGENT : Found MT6753

AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
NAND : DEVICE NOT FOUND
NAND : 000000000000000000000000
eMMC : OK
eMMC : 90014A484247346132A4235205284AFB
DAInf: 4 : 2 : 155
DA : EXT_RAM NOT initialized!
eMMC : OK
eMMC : 484A0190613447425223A432FB4A2805
NAND : DEVICE NOT FOUND
NAND : 000000000000000000000000
EMI : DEV : INFINITY
EMI : SRC : INFINITY-BOX_INTERNAL_EMIDB_v0
INIT : 0xBC : LP/DDR3 [ 0x00000000 : [ 0 B ] ]
DRAM : DRAM: 0xC0000000 [ 3.00 GB ]
DA : DRAM ready!
DA : BOOT to 2nd DA ...
DA : Receiving HW info

EMMC: 90014A484247346132A4235252883FB
EMMC: VEN : HYNIX | OEM : 4A01 | DEV : HBG4a2
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x00400000 [ 4.00 MB ]
USER : 0x747C00000 [ 29.12 GB ]

SRAM: 0x00020000 [ 128.00 KB ]
DRAM: 0xC0000000 [ 3.00 GB ]

CHIP : MT6753 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

RNID : B0BBE292E34250FA7420829E274D7F8

STATUS : BLANK FLASH
BSTYLE : EMMC FLASH BOOT

DA : USB : FULL-SPEED
DA : USB : Change Port Speed
PTFN : MediaTek DA USB VCOM (Android) (COM91)
MODE : PRELOADER PORT
PORT : 91

Boot done!

Format Ok : RESET PROTECTION

Done!
Elapsed: 00:00:16

Reconnect Power/Cable!
THANKS INFINITY-BOX TEAM
gracy_elec
Posts: 34
Joined: 07 Jul 2019, 04:59

VIVO Y15 1901 AND:9 MT6765 READ NVRAM BAG & BRUSH PATTERN & FRP Done

Post by gracy_elec »

SUCCESSFULLY READ NVRAM BAG & BRUSH PATTERN & FRP DONE(VIVO Y15 1901 AND:9 MT6765)USB

Operation : Identify [ v2.06 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM (Android) (COM34)
MODE : PRELOADER PORT
PORT : 34
Waiting BOOT ack ...
PRELOADER : ACK confirm FAIL!
BROM : Init BROM
BROM init passed!
CHIP : MT6765 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
TYPE : MODERN RAPHAEL
BROM : SecLevel : 0x00000005
BROM : SecMode : SBC+SDA
BROM : PRELOADER PORT
MODE : Vivo : Y83 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA_VIP.bin
AGENT : Found MT6765

AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : PRELOADER
DA : EXT_RAM initialized!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

SRAM: 0x00040000 [ 256.00 KB ]
DRAM: 0x30000000 [ 768.00 MB ]

EMMC: 150100525036344D4201D5C5E439462B
EMMC: VEN : SAMSUNG | OEM : 01 | DEV : RP64MB
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x01000000 [ 16.00 MB ]
USER : 0xE8F800000 [ 58.24 GB ]

CHIP : MT6765 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

RNID : C6EA1443EB24C68FE4D592EEF6169C19

DA : USB : HIGH-SPEED

Boot done!

Patch Level : PPR1.180610.011
Display ID : PPR1.180610.011 release-keys
Ver. CodeName : REL
Ver. Release : 9
Sec. Patch : 2019-07-05
Build Time : 1562602055
Product Model : vivo 1901
Product Brand : vivo
Product Name : PD1901BF_EX
Product Device : PD1901BF_EX
Product Manfct : vivo
Product Info : k62v1_64_bsp
Product Board : k62v1_64_bsp
Board Platform : mt6765

USERDATA : ENCRYPTED

NVRAM check : Passed!

Backup sensetive data [ 10 ]
Backup path : Backup\MT6765__C6EA1443EB24C68FE4D592EEF6169C19\
[29] Read : NVRAM
[8] Read : NVDATA
[19] Read : PROINFO
[30] Read : LK
[7] Read : NVCFG
[14] Read : PROTECT1
[15] Read : PROTECT2
[17] Read : PERSIST
[0] Read : PRELOADER
Backup done!



Done!
Elapsed: 00:00:32

Operation : Reset Settings/Format FS [ v2.06 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM (Android) (COM34)
MODE : PRELOADER PORT
PORT : 34
Waiting BOOT ack ...
PRELOADER : ACK confirmed!
BROM : Init BROM
BROM init passed!
CHIP : MT6765 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
TYPE : MODERN RAPHAEL
BROM : SecLevel : 0x00000005
BROM : SecMode : SBC+SDA
BROM : PRELOADER PORT
MODE : Vivo : Y83 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA_VIP.bin
AGENT : Found MT6765

AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : PRELOADER
DA : EXT_RAM initialized!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

SRAM: 0x00040000 [ 256.00 KB ]
DRAM: 0x30000000 [ 768.00 MB ]

EMMC: 150100525036344D4201D5C5E439462B
EMMC: VEN : SAMSUNG | OEM : 01 | DEV : RP64MB
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x01000000 [ 16.00 MB ]
USER : 0xE8F800000 [ 58.24 GB ]

CHIP : MT6765 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

RNID : C6EA1443EB24C68FE4D592EEF6169C19

DA : USB : HIGH-SPEED

Boot done!

Format Ok : USERDATA
Format Ok : CACHE
Format Ok : RESET PROTECTION
Format Ok : USERDATA


Done!
Elapsed: 00:00:38

Reconnect Power/Cable!

Operation : Memory Tool Init [ v2.06 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek PreLoader USB VCOM (Android) (COM34)
MODE : PRELOADER PORT
PORT : 34
Waiting BOOT ack ...
PRELOADER : ACK confirmed!
BROM : Init BROM
BROM init passed!
CHIP : MT6765 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
TYPE : MODERN RAPHAEL
BROM : SecLevel : 0x00000005
BROM : SecMode : SBC+SDA
BROM : PRELOADER PORT
MODE : Vivo : Y83 | Manual : Disabled
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA_VIP.bin
AGENT : Found MT6765

AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : PRELOADER
DA : EXT_RAM initialized!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

SRAM: 0x00040000 [ 256.00 KB ]
DRAM: 0x30000000 [ 768.00 MB ]

EMMC: 150100525036344D4201D5C5E439462B
EMMC: VEN : SAMSUNG | OEM : 01 | DEV : RP64MB
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x01000000 [ 16.00 MB ]
USER : 0xE8F800000 [ 58.24 GB ]

CHIP : MT6765 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000

RNID : C6EA1443EB24C68FE4D592EEF6169C19

DA : USB : HIGH-SPEED

Boot done!

Set default path : C:\InfinityBox\CM2MT2\phdata\

Ready!

Operation : Erase Memory

Erase selected partitions [3]
[0] Erase partition : FRP
Erase partition Ok!
[1] Erase partition : CACHE
Erase partition Ok!
[2] Erase partition : USERDATA
Erase partition Ok!

Operation finished!


Close MemoryTool session


Done!
Elapsed: 00:00:38

Reconnect Power/Cable!
THANKS INFINITY-BOX TEAM
gracy_elec
Posts: 34
Joined: 07 Jul 2019, 04:59

OPPO F5 CPH1723 AND:7.1.1 MT6763A READ NVRAM BAG & BRUSH PATTERN & FRP Done

Post by gracy_elec »

SUCCESSFULLY READ NVRAM BAG & BRUSH PATTERN & FRP DONE(OPPO F5 CPH1723 AND:7.1.1 MT6763A)USB

Operation : Identify [ v2.06 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek USB Port (COM107)
MODE : BOOTROM
PORT : 107
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6763 , SBID : 0x8A00 , HWVR : 0xCA01 , SWVR : 0x0001
TYPE : MODERN RAPHAEL
BROM : SecLevel : 0x000000E5
BROM : SecMode : SBC+SDA+ARB
BROM : BOOTROM
MODE : Oppo : F5 | Manual : Disabled
BROM : ARB : ACTIVE : LOG : F0: 102B 0000 F3: 4000 0036 F7: 102D 0000 00: 1005 0000 F3: 4000 0036 F7: 102D 0000 01: 102A 0001

BROM : SOCID : C50C1BA93548BC30E7CFFBDD97D317FD2F7015407188792EC55B136EC6E7B9F7
BROM : SLA
BROM : SLA Passed!
BROM : SLA CHLNG not used
AGENT : Look for suitable BootChain in DA ...
AGENT : DA_PL_CRYPTO.bin
AGENT : Found MT6763

AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : BROM
DA : EXT_RAM NOT initialized!
EMI : DEV : MT6763
EMI : SRC : preloader_oppo6763_17031.bin
EMI : CNT : 000F
EMI : [00] : DRAM : EXTERNAL DRAM [LP/DDR4] , UNDEFINED : VEN : UNKNOWN | DEV : : RAM : [ 0 B ]
EMI : [01] : eMCP : eMMC+LP/DDR4 , ID : 150100444836444D42 : VEN : SAMSUNG | DEV : DH6DMB : RAM : [ 4.00 GB ]
EMI : [02] : eMCP : eMMC+LP/DDR3 , ID : 150100525836344D42 : VEN : SAMSUNG | DEV : RX64MB : RAM : [ 4.00 GB ]
EMI : [03] : eMCP : eMMC+LP/DDR3 , ID : 150100524836344142 : VEN : SAMSUNG | DEV : RH64AB : RAM : [ 4.00 GB ]
EMI : [04] : eMCP : eMMC+LP/DDR4 , ID : 150100334836434D42 : VEN : SAMSUNG | DEV : 3H6CMB : RAM : [ 6.00 GB ]
EMI : [05] : eMCP : eMMC+LP/DDR3 , ID : 150100524836344D42 : VEN : SAMSUNG | DEV : RH64MB : RAM : [ 4.00 GB ]
EMI : [06] : eMCP : eMMC+LP/DDR3 , ID : 150100474436424D42 : VEN : SAMSUNG | DEV : GD6BMB : RAM : [ 3.00 GB ]
EMI : [07] : eMCP : eMMC+LP/DDR3 , ID : 150100475836424D42 : VEN : SAMSUNG | DEV : GX6BMB : RAM : [ 3.00 GB ]
EMI : [08] : eMCP : eMMC+LP/DDR3 , ID : 150100474536424D42 : VEN : SAMSUNG | DEV : GE6BMB : RAM : [ 3.00 GB ]
EMI : [09] : eMCP : eMMC+LP/DDR3 , ID : 150100524436344D42 : VEN : SAMSUNG | DEV : RD64MB : RAM : [ 4.00 GB ]
EMI : [0A] : eMCP : eMMC+LP/DDR3 , ID : 13014E53304A394237 : VEN : MICRON | DEV : S0J9B7 : RAM : [ 3.00 GB ]
EMI : [0B] : DRAM : EXTERNAL DRAM [LP/DDR3] , UNDEFINED : VEN : UNKNOWN | DEV : : RAM : [ 4.00 GB ]
EMI : [0C] : DRAM : EXTERNAL DRAM [LP/DDR4] , UNDEFINED : VEN : UNKNOWN | DEV : : RAM : [ 4.00 GB ]
EMI : [0D] : DRAM : EXTERNAL DRAM [LP/DDR3] , UNDEFINED : VEN : UNKNOWN | DEV : : RAM : [ 3.00 GB ]
EMI : [0E] : DRAM : EXTERNAL DRAM [LP/DDR4] , UNDEFINED : VEN : UNKNOWN | DEV : : RAM : [ 6.00 GB ]
EMI : Init EMI from PRELOADER
EMI : EXT_RAM CFG Passed!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

SRAM: 0x00040000 [ 256.00 KB ]
DRAM: 0xC0000000 [ 3.00 GB ]

EMMC: 150100525836344D420371CEDA6D749B
EMMC: VEN : SAMSUNG | OEM : 01 | DEV : RX64MB
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x00400000 [ 4.00 MB ]
USER : 0x747C00000 [ 29.12 GB ]

CHIP : MT6763 , SBID : 0x8A00 , HWVR : 0xCA01 , SWVR : 0x0000 , EVOL : 0x0000

RNID : 89773E96962CF3D323A211B4B3FB7205

DA : USB : HIGH-SPEED

Boot done!

Patch Level : N6F26Q
Ver. CodeName : REL
Ver. Release : 7.1.1
Sec. Patch : 2019-08-05
Build Time : 1565771588
Product Manfct : OPPO
Board Platform : mt6763
Product Model : OPPO CPH1723
Product Brand : OPPO
Product Name : CPH1723
Product Device : M6763A
Product Board : full_oppo6763_17031
Product Info : oppo6763_17031
SW Version : A.38
SW OTA Version : M6763A_11.A.38_0380_201908141524
SW OTA Name : CPH1723EX_11_A.38_190814
Display ID : CPH1723EX_11_A.38_190814
Kernel Info : 4.4.22-G201908141524

USERDATA : ENCRYPTED

NVRAM check : Passed!

Backup sensetive data [ 10 ]
Backup path : Backup\MT6763__89773E96962CF3D323A211B4B3FB7205\
[28] Read : NVRAM
[13] Read : NVDATA
[20] Read : PROINFO
[29] Read : LK
[12] Read : NVCFG
[15] Read : PROTECT1
[16] Read : PROTECT2
[18] Read : PERSIST
[0] Read : PRELOADER
Backup done!



Done!
Elapsed: 00:03:01

Operation : Reset Settings/Format FS [ v2.06 ]

1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...

PTFN : MediaTek USB Port (COM107)
MODE : BOOTROM
PORT : 107
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6763 , SBID : 0x8A00 , HWVR : 0xCA01 , SWVR : 0x0001
TYPE : MODERN RAPHAEL
BROM : SecLevel : 0x000000E5
BROM : SecMode : SBC+SDA+ARB
BROM : BOOTROM
MODE : Oppo : F5 | Manual : Disabled
BROM : ARB : ACTIVE : LOG : F0: 102B 0000 F3: 4000 0036 F7: 102D 0000 00: 1005 0000 F3: 4000 0036 F7: 102D 0000 01: 102A 0001

BROM : SOCID : C50C1BA93548BC30E7CFFBDD97D317FD2F7015407188792EC55B136EC6E7B9F7
BROM : SLA
BROM : SLA Passed!
BROM : SLA CHLNG not used
AGENT : Look for suitable BootChain in DA ...
AGENT : DA_PL_CRYPTO.bin
AGENT : Found MT6763

AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : BROM
DA : EXT_RAM NOT initialized!
EMI : DEV : MT6763
EMI : SRC : preloader_oppo6763_17031.bin
EMI : CNT : 000F
EMI : [00] : DRAM : EXTERNAL DRAM [LP/DDR4] , UNDEFINED : VEN : UNKNOWN | DEV : : RAM : [ 0 B ]
EMI : [01] : eMCP : eMMC+LP/DDR4 , ID : 150100444836444D42 : VEN : SAMSUNG | DEV : DH6DMB : RAM : [ 4.00 GB ]
EMI : [02] : eMCP : eMMC+LP/DDR3 , ID : 150100525836344D42 : VEN : SAMSUNG | DEV : RX64MB : RAM : [ 4.00 GB ]
EMI : [03] : eMCP : eMMC+LP/DDR3 , ID : 150100524836344142 : VEN : SAMSUNG | DEV : RH64AB : RAM : [ 4.00 GB ]
EMI : [04] : eMCP : eMMC+LP/DDR4 , ID : 150100334836434D42 : VEN : SAMSUNG | DEV : 3H6CMB : RAM : [ 6.00 GB ]
EMI : [05] : eMCP : eMMC+LP/DDR3 , ID : 150100524836344D42 : VEN : SAMSUNG | DEV : RH64MB : RAM : [ 4.00 GB ]
EMI : [06] : eMCP : eMMC+LP/DDR3 , ID : 150100474436424D42 : VEN : SAMSUNG | DEV : GD6BMB : RAM : [ 3.00 GB ]
EMI : [07] : eMCP : eMMC+LP/DDR3 , ID : 150100475836424D42 : VEN : SAMSUNG | DEV : GX6BMB : RAM : [ 3.00 GB ]
EMI : [08] : eMCP : eMMC+LP/DDR3 , ID : 150100474536424D42 : VEN : SAMSUNG | DEV : GE6BMB : RAM : [ 3.00 GB ]
EMI : [09] : eMCP : eMMC+LP/DDR3 , ID : 150100524436344D42 : VEN : SAMSUNG | DEV : RD64MB : RAM : [ 4.00 GB ]
EMI : [0A] : eMCP : eMMC+LP/DDR3 , ID : 13014E53304A394237 : VEN : MICRON | DEV : S0J9B7 : RAM : [ 3.00 GB ]
EMI : [0B] : DRAM : EXTERNAL DRAM [LP/DDR3] , UNDEFINED : VEN : UNKNOWN | DEV : : RAM : [ 4.00 GB ]
EMI : [0C] : DRAM : EXTERNAL DRAM [LP/DDR4] , UNDEFINED : VEN : UNKNOWN | DEV : : RAM : [ 4.00 GB ]
EMI : [0D] : DRAM : EXTERNAL DRAM [LP/DDR3] , UNDEFINED : VEN : UNKNOWN | DEV : : RAM : [ 3.00 GB ]
EMI : [0E] : DRAM : EXTERNAL DRAM [LP/DDR4] , UNDEFINED : VEN : UNKNOWN | DEV : : RAM : [ 6.00 GB ]
EMI : Init EMI from PRELOADER
EMI : EXT_RAM CFG Passed!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info

SRAM: 0x00040000 [ 256.00 KB ]
DRAM: 0xC0000000 [ 3.00 GB ]

EMMC: 150100525836344D420371CEDA6D749B
EMMC: VEN : SAMSUNG | OEM : 01 | DEV : RX64MB
EMMC:
BOOT1 : 0x00400000 [ 4.00 MB ]
BOOT2 : 0x00400000 [ 4.00 MB ]
RPMB : 0x00400000 [ 4.00 MB ]
USER : 0x747C00000 [ 29.12 GB ]

CHIP : MT6763 , SBID : 0x8A00 , HWVR : 0xCA01 , SWVR : 0x0000 , EVOL : 0x0000

RNID : 89773E96962CF3D323A211B4B3FB7205

DA : USB : HIGH-SPEED

Boot done!

Format Ok : USERDATA
Format Ok : CACHE
Format Ok : RESET PROTECTION
Format Ok : USERDATA


Done!
Elapsed: 00:00:46

Reconnect Power/Cable!
THANKS INFINITY-BOX TEAM
Post Reply